26 July 2019 in Macromolecular Rapid Communications
7 October 2016 in Scientific Reports
In the report we demonstrate how, using laser light, effectively trap gas bubbles and transport them through a liquid phase to a desired destination by shifting the laser beam position. The physics underlying the effect is complex but quite general as it comes from the limited to two-dimension, well-known, Marangoni effect. The experimental microscope-based system consists of a thin layer of liquid placed between two glass plates containing a dye dissolved in a solvent and a laser light beam that is strongly absorbed by the dye. This point-like heat source locally changes surface tension of nearby liquid-air interface. Because of temperature gradients a photo-triggered Marangoni flows are induced leading to self-amplification of the effect and formation of large-scale whirls. The interface is bending toward beam position allowing formation of a gas bubble upon suitable beam steering. Using various techniques (employing luminescent particles or liquid crystals), we visualize liquid flows propelled by the tangential to interface forces. This helped us to understand the physics of the phenomenon and analyze accompanying effects leading to gas bubble trapping. The manipulation of sessile droplets moving on the glass surface induced via controlled with laser light interface bending (i.e. “droplet catapult”) is demonstrated as well.
4 April 2023 in Nature Communications
Despite spectacular progress in microfluidics, small-scale liquid manipulation, with few exceptions, is still driven by external pumps and controlled by large-scale valves, increasing cost and size and limiting complexity. By contrast, optofluidics uses light to power, control and monitor liquid manipulation, potentially allowing for small, self-contained microfluidic devices. Here we demonstrate a soft light-propelled actuator made of liquid crystal gel that pumps microlitre volumes of water. The strip of actuating material serves as both a pump and a channel leading to an extremely simple microfluidic architecture that is both powered and controlled by light. The performance of the pump is well explained by a simple theoretical model in which the light-induced bending of the actuator competes with the liquid’s surface tension. The theory highlights that effective pumping requires a threshold light intensity and strip width. The proposed system explores the benefits of shifting the complexity of microfluidic systems from the fabricated device to spatio-temporal control over stimulating light patterns.
29 January 2020 in ACS Applied Materials & Interfaces
The photomechanical response of liquid crystal polymer networks (LCNs) can be used to directly convert light energy into different forms of mechanical energy. In this study, we demonstrate how a traveling deformation, induced in a liquid crystal polymer ring by a spatially modulated laser beam, can be used to drive the ring (the rotor) to rotate around a stationary element (the stator), thus forming a light-powered micromotor. The photomechanical response of the polymer film is modeled numerically, different LCN molecular configurations are studied, and the performance of a 5.5 mm diameter motor is characterized.
5 February 2024 in Soft Matter
We combine theory and experiments to explore the kinematics and actuation of intrinsically curved folds (ICFs) in otherwise developable shells. Unlike origami folds, ICFs are not bending isometries of flat sheets, but arise via non-isometric processes (growth/moulding) or by joining sheets along curved boundaries. Experimentally, we implement both, first making joined ICFs from paper, then fabricating flat liquid crystal elastomer (LCE) sheets that morph into ICFs upon heating/swelling via programmed metric changes. Theoretically, an ICF's intrinsic geometry is defined by the geodesic curvatures on either side, $\kappa_{g_i}$. Given these, and a target 3D fold-line, one can construct the entire surface isometrically, and compute the bending energy. This construction shows ICFs are bending mechanisms, with a continuous family of isometries trading fold angle against fold-line curvature. In ICFs with symmetric $\kappa_{g_i}$, straightening the fold-line culminates in a fully-folded flat state that is deployable but weak, while asymmetric ICFs ultimately lock with a mechanically strong finite-angle. When unloaded, freely-hinged ICFs simply adopt the (thickness $t$ independent) isometry that minimizes the bend energy. In contrast, in LCE ICFs a competition between flank and ridge selects a ridge curvature that, unusually, scales as $t^{-1/7}$. Finally, we demonstrate how multiple ICFs can be combined in one LCE sheet, to create a versatile intrinsically curved gripper that lifts a heavy weight.
5 January 2016 in Physical Chemistry Chemical Physics
Using the direct coupling mechanism of light with a liquid via molecular absorption, i.e. the opto-thermal effect, we demonstrate the formation of well-controlled three-dimensional circular flows, i.e. a toroidal vortex, inside the liquid crystal (LC) droplet placed on a glass plate in its isotropic phase. We investigated the behavior of a droplet formed of a phototropic liquid crystal and composed of a mesogenic azobenzene derivative under the Gaussian beam light illumination in four different geometries. The light-induced liquid flows in the isotropic phase of the LC were visualized by dispersing carbon micro-particles in the volume of the LC. Movements of the particles could be observed under an optical microscope from the top and side views, respectively. The formation of the stable in time toroidal vortex (the photonic vortex) is dependent on laser light illumination geometry, properties of the liquid and substrate but does not depend on gravitational forces being similar for droplets situated either above or below the glass plate. The main mechanism of the indirect conversion of light into mechanical work is related to the temperature induced gradient of surface tension known as the Marangoni effect.