23 April 2019 in IEEE Sensors Journal
Recently, the parameter estimation and focusing of ground moving target in the circular SAR (CSAR) attracts widely interest in researchers. In this paper, a sub-aperture-based frequency domain algorithm that divides the CSAR trajectory into sub-apertures is proposed, which achieves better focusing quality than that of the traditional straight-line fitting method. Firstly, the CSAR sub-aperture is fitted by a parabola with special curvature, and the effectiveness of this fitting is analyzed. Next, a parameter estimation method is proposed to estimate the motion parameters of the ground moving target for each sub-aperture. Finally, the moving target is refocused based on the estimation results. Simulation as well as the real CSAR data processing results verified the theoretical analysis of the proposed method.
10 October 2024 in IEEE Transactions on Geoscience and Remote Sensing
The acquisition of 3D information in the observation scene has always been a prominent issue in the field of synthetic aperture radar (SAR). The emerging Wide-angle staring SAR (WasSAR) utilizes its unique multi-view observation performance to obtain offset information of the target position under different observation angles, enabling the acquisition of 3D information of the observation scene. However, existing multi-view 3D information extraction methods suffer from large errors due to a lack of prior information about the observed scene. In order to address these challenges, this paper analyses the impact of the missing incidence angle information on the 3D reconstruction results, and proposes a 3D information correction algorithm. The method only needs the single-channel echo information of the two azimuth angles of a single pass, and the corresponding radar platform motion information, and does not need to rely on any a priori information of the observation scene, which realizes the acquisition of 3D information without a priori information in the real sense. Through simulation experiments, we quantitatively analyze the error transfer coefficient and confirm both accuracy and effectiveness through experimental data processing in Ku-band mountain scenes autonomously measured by our team. The proposed algorithm significantly enhances measurement precision and reliability, demonstrating a Mean Error reduction to just 49% and a Root Mean Square Error (RMSE) decrease to 46% compared to the traditional method, thereby confirming its superior performance and practicality.
29 October 2024 in IEEE Transactions on Geoscience and Remote Sensing
The low-band synthetic aperture radar (SAR) is a system which can present foliage penetrating (FP) targets and exposed strong-scattering targets while the high-band SAR system can present exposed targets and the texture information except for FP targets. Therefore, the difference feature of co-registered low-band and high-band SAR images can theoretically reveal FP targets with some disturbances. However, the co-registered dual-band SAR images cannot do the difference operator directly for the distinct statistical property of the SAR image pair. The traditional method is to transfer the background texture from the high-band SAR image to the low-band SAR image by the cycle-consistent generative adversarial network (CGAN) method. However, CGAN would generate the discontinuity and mistake in transferring the large-scale texture information and the complex network would heavily increase the time complexity in the application. To overcome this issue, we first innovatively introduce a fast and accurate texture transferring method based on the dual-band SAR image fusion (DBIF), then we further combine the DBIF based texture transferring method with the difference operator and the threshold segmentation, and finally we get a novel DBIF based FP target detection (DBIFFPTD) method. To verify the feasibility of the DBIF based texture transfer method, we discuss the reflection form of different landscape objects at dual-band waves and estimate the theoretical texture transferring image. Experiments on the open dual-band AIR-MD-SAR dataset and the independently measured dual-band SAR dataset show that the novel DBIF performs better than CGAN in transferring texture information of dual-band SAR images. Besides, dual-band linear SAR (LSAR) and circular SAR (CSAR) foliage penetrating experiments are both conducted to show that the proposed DBIFFPTD has a wide applicability in the flight track and is superior to the traditional low-band double-parameter constant false alarm rate (DCFAR) detector based FPTD (DCFARFPTD) method and dual-band CGAN based FPTD (CGANFPTD) method.
25 December 2023 in IEEE Journal of Selected Topics in Applied Earth Observations and Remote Sensing
The generation of high-precision ground digital elevation models (DEMs) based on synthetic aperture radar interferometry (InSAR) technology has attracted wide attention. Compared with the linear InSAR technique, the 360° aperture gives circular InSAR (In-CSAR) the capability to generate a full-angle DEM of the observed region. The backprojection (BP) algorithm is considered as a preferred candidate for InCSAR imaging since it does not impose any restrictions on flight trajectories. After phase unwrapping, a global unknown phase ambiguity exists in the unwrapped phase. Up to now, highefficient frequency-domain methods, such as the split-bandwidth technique, have commonly been used to estimate the phase ambiguity. However, the split-bandwidth technique cannot be effectively integrated with the BP-focusing image due to the highly nonlinear and nonparallel trajectories of the airborne In-CSAR platforms. We present, for the first time, the combination of BP and split-bandwidth techniques for absolute phase estimation of In-CSAR interferogram in this paper. The proposed method can avoid the phase offset induced by split-bandwidth processing under the conditions of highly nonlinear and nonparallel platform trajectories. In addition, the spectral characteristics of the BPfocusing subimage are derived in detail to correct its 2-D spacevariant spectral support. In order to reduce the impact of coherence, the weighted least square (WLS) is adopted to estimate unknown phase ambiguity. The processing results of simulation and real data verify that the proposed approach can effectively estimate the phase ambiguity even under the conditions of highly nonlinear and nonparallel platform trajectories.
20 December 2023 in IEEE Sensors Journal
In recent years, the generation of high-precision ground digital elevation models (DEMs) based on synthetic aperture radar interferometry (InSAR) technology has attracted wide attention. Compared with the traditional linear InSAR technique, a 360° aperture gives circular InSAR (In-CSAR) the capability to generate a full-angle DEM of the observed region. Due to the highly nonlinear platform trajectories, the back projection algorithm (BPA) is used to obtain the subimages and interferograms. In this paper, spectral characteristics of the BP-focusing subimages, including 2-D spectral ambiguity and space-variant spectral support, are derived in detail. Using these characteristics, an improved BPA to ensure the accuracy of the interferograms is proposed, which takes the shape and position of the subaperture into consideration. Without external DEM, an effective method of full-angle DEM generation is proposed for an airborne repeat-pass L-band In-CSAR system. Based on the weighted fusion of multiple observations, the proposed subaperture strategy can improve the accuracy of the full-angle DEM. The experimental results indicate that proposed strategy can generate more accurate DEMs (with an average error of 0.69 m). Moreover, the first real 360° DEM results acquired by our developed L-band In-CSAR system are given in this paper. The effectiveness and practicability of the proposed approach is verified with the processing results of simulation and real data.
13 June 2024 in IEEE Transactions on Geoscience and Remote Sensing
For airborne repeat-pass synthetic aperture radar interferometry (InSAR), residual motion errors (RMEs) exist between the true and measured trajectories due to the inaccuracy of current navigation systems. In addition, a global unknown phase ambiguity (PA) exists in the unwrapped phase due to the error of absolute phase estimation. The RME and PA are significant error sources in the repeat-pass InSAR, which can cause phase errors in the final interferograms. In general, an external digital elevation model (DEM) can be used to estimate the RME and PA. However, it is hard to find a high-precision external DEM matching with the airborne InSAR data. Compared with the traditional InSAR technique, the 360° aperture gives circular InSAR (In-CSAR) the capability to estimate the RME and PA without external DEMs. Unlike previous approaches, in this paper, a multi-angle observation model is established to estimate RME and PA simultaneously. This model registers the DEM images obtained from different observation angles. In the field of image registration, the Demons algorithm is often used for non-rigid registration. We use, for the first time, the Demons algorithm to register multi-angle false DEM images containing height errors and obtain the reference DEMs. Due to the gradient of the DEM image being destroyed by the RME and PA, a two-step preprocessing is proposed to achieve sub-pixel registration of multi-angle false DEM images. After obtaining the reference DEM, the least square (LS) or robust mixed integer linear programming (RMILP) can estimate the unknown RME and PA. The results show that, with respect to the true values, the root-mean-square error (RMSE) of the calibrated DEMs is 0.37 m for the simulated data set and 1.17 m for the real data set. After correcting the RME-induced and PA-induced height errors, the RMSE of the DEM is improved by at least 92.6 % for the simulated data set and by at least 70.8 % for the real data set.