23 February 2018 in IEEE Transactions on Industrial Electronics
This paper presents the concept of a spherical-motor-based motion platform (SMP) for providing high-performance nozzle-substrate negotiation in conformal printing of curved electronics. Unlike conventional motion systems using serial/parallel mechanisms for multi-DOF rotations, a ball-joint-like spherical motor for providing continuous 3-DOF rotations in one joint is designed to meet the special needs of the conformal printing process. Both the kinematic and dynamic models of the SMP are presented for fitting into the conformal printing process. Specifically, the performance of a spherical motor has been evaluated, which shows better negotiation capability of the SMP than traditional motion systems. The experimental test results performed on a prototype spherical motor have validated the design concept.
11 March 2024 in Ocean Engineering
14 June 2022 in IEEE Transactions on Automation Science and Engineering
A solar tracker significantly increases the amount of energy harvested by a floating photovoltaic system by adjusting the pose of its photovoltaic (PV) panels to optimize their exposure to the solar rays. Conventional solar trackers perform such an adjustment using actuators, which is energy-consuming and involves complex structures. In this paper, a novel dual-axis wave-driven solar tracker is proposed where the photovoltaic (PV) panel is adjusted by the inertia force and gravity. Actuators are replaced by brakes to fix the pose of the PV panel. The kinematics and dynamics of the system are investigated, which are further used for the state feedback and the formulation of the control strategy. A sliding-mode observer is used to estimate the effect of winds on the system, which enables the robustness of the system to be enhanced. A motion planning strategy is also developed to track the solar position and minimize the movements of two joints. Indoor experiments are conducted to test the accuracy of the state feedback and dynamic model. The performance of the uncertainty observer is also tested by experiments. At last, field experiments on the real water surface are implemented to verify the feasibility of the proposed system. The results show that the solar tracker is able to adjust the PV panels at a velocity of 8.89 deg/s under the effect of limited base motions with amplitude less than 4 $^{\circ}$ . Note to Practitioners—Traditional solar trackers can be driven passively by chemical energy or actively using actuators. The former cannot function stably in the field environment, and the latter is complex in structure and energy-consuming. For the FPV system under the effect of waves, the solar tracker can utilize the motion of the base to align its PV panel to the solar position. Thus, we present a wave-driven solar tracker without using actuators, and brakes are applied to lock the position of joints. The proposed solar tracker is energy-efficient, has a simpler structure and hardware than the active one, and is more robust than the passive one. We model the system and propose a control scheme to drive the PV panel using inertia and gravity. We also observe the effect of winds to enhance the system robustness. The motion planning strategy is investigated to minimize the movements of the joints. The impact of base motion and control period on the energy-harvesting efficiency is analyzed by simulations. Both indoor and field experiments are implemented to verify the feasibility of the system. The experimental results show that the system performs well even when the base shacking is less than 4 $^\circ$ . Note that the control algorithm is a model-based algorithm, which means the model parameters (inertia, gravity, etc.) need to be reidentified for different PV panels and system properties. That is a challenge for large-scale deployment with different configurations. Future research will address the system identification problem and enable the model parameters to be updated automatically.
18 September 2024 in IEEE Transactions on Robotics
Capturing stationary aerial objects on unmanned surface vehicles (USVs) is challenging due to quasiperiodic and fast floating-base motions caused by wave-induced disturbances. It is hard to (1) maintain high motion prediction accuracy due to the stochastic nature of these disturbances and (2) perform object capture through real-time tracking due to the limited active torque. We introduce confidence analysis in predictive capture. To address the inaccuracy predictions, we calculate a real-time confidence tube to evaluate the prediction quality. To overcome tracking difficulties, we plan a trajectory to capture the object at a future moment while maximizing the confidence of the capture position on the predicted trajectory. All calculations are completed within 0.2 seconds to ensure a timely response. We validate our approach through experiments, where we simulate disturbances by executing real USV motions using a servo platform. The results demonstrate that our method achieves an 80% success rate.
10 February 2023 in IEEE Robotics and Automation Letters
The docking mechanism is critical for unmanned surface vehicle (USV) applications, such as traction, dragging, charging, data transmission, building pontoons, etc. These applications are significant for observation, exploration, data acquisition, patrol, rescuing, etc., in aquatic environments. In this letter, a novel autonomous docking mechanism for USVs is proposed. It is capable of (1) docking the USV subject to disturbance efficiently, (2) latching without power consumption after the docking is completed, and (3) guiding the docking head to three specific angles at the end of the docking process. This letter proved the feasibility and rationality of the docking mechanism through theoretical force analysis. Experiments with three different scenarios are implemented to test the mechanism's performance. The experimental results show that the docking success rate is greater than or equal to 90 $\%$ on the disturbed water surface.
17 April 2025 in IEEE/ASME Transactions on Mechatronics
Magnetically actuated robotic devices are gaining increasing attention in medical applications. Robotic devices based on permanent magnets are better suited for the human body due to their wide workspace for operation. For these devices, handling the motion constraints of external permanent magnets (EPM) reasonably is crucial for safety. These constraints include motion range and obstacles, and the internal permanent magnet (IPM) motion needs to be controlled simultaneously. Existing hierarchical control structures usually design the controllers for the IPM and the manipulator separately. This makes it difficult to simultaneously satisfy the movement constraints of the EPM and the control accuracy of the IPM. To address this problem, we model the manipulator and IPM as a whole body and yield control command by formulating an optimization problem. We simplify the model and formulate a real-time iteration model predictive controller (RTI-MPC) to improve computational efficiency, and the control frequency reaches 30 Hz in actual deployment. We have validated the feasibility and tested the performance of this method through simulations and experiments. The experiments demonstrate that the manipulator can successfully control the IPM through the colon phantom while avoiding obstacles in the task space.