Feliks Ya. Rudik

Feliks Ya. Rudik

Auto-generated profile, based on publicly available information

Feliks Ya. Rudik

Saratov State Vavilov Agrarian University, 1 Teatralnaya Square, Saratov, 410012, Russia

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2020 in IOP Conference Series: Earth and Environmental Science
Verified
Conference Paper
Open access
FRF Ya Rudik
F Ya Rudik
NMN L Morgunova
N L Morgunova
EKE S Krasnikova
E S Krasnikova
The article considers the method of grain processing in the medium of an anolyte, produced at the STEL type plant, with subsequent washing and drying to a humidity of not more than 14%. Decontamination of grain was carried out by ultrasound of low frequencies 24-26 kHz with ultrasound intensity no more than 1 W/cm2. The method provides a reduction in the content of mold fungi in the grain, prevents the development of mycotoxins in it, reduces contamination with mineral impurities and insect pest.

31 December 2019 in Engineering Technologies and Systems
Verified
Journal Article
Open access
AAAlexander V. Anisimov
Alexander V. Anisimov
FRFelix Ya. Rudik
Felix Ya. Rudik
Introduction. Modern technology of grain processing pays special attention to the qualitative and efficient preparation of grain for milling. At small enterprises with a reduced technological process, this is almost the only way to improve product yield and quality. Without proper multi-stage preparation of grain for milling at small enterprises, it is impossible to achieve the required quality and quantity of products produced by industrial mills. Grain peeling is one of the most effective ways to clean the surface from dirt and remove outer shells. The removal of outer shells allows increasing the yield of high-grade flour at reduced milling diagrams. The efficiency of the peeling process is significantly infuencet by the design and operating parameters of the peeling machine. The purpose of this work is the experimental determination of optimal conditions for grain processing in the peeling and drying machine (the optimal combination of factors). Materials and Methods. To determine optimal conditions for grain processing in the peeling and drying machine, the method of extreme planning of the experiment was applied. The method of random balance was used to select the most significant factors based on their influence on the optimization parameter. The method of steep ascent on the response surface (the Box – Wilson method) was used to find the optimum area (the planning matrix was realized and statistical analysis of results and steep ascent on the response surface was carried out). Verification of the results was carried out on the software Statistica 10.0. Results. On the basis of experiments, a mathematical model of the technological process of wheat processing in the peeling and drying machine there were obtained, which linked the structural and mode parameters of the machine with the humidity of the treated grain. The results of the experiment confirmed the operability of the developed machine when working with high-humidity grain; they are fundamental for the machine’s further modernization. Discussion and Conclusion The analysis of the controlled factor dispersion diagram allowed us to select the most significant of them based on influence on the selected optimization parameter, the white flour color obtained from the treated grain. As a result of the evaluation of experimental data of the conducted studies, the design and mode parameters of the developed machine were determined, corresponding to the areas of the optimal optimization parameter: shaft rotation speed is 1400 rpm, angle of inclination of stamping on the sieve drum is 15 degrees, the initial moisture content of the processed grain is 15.50%, and the machine productivity does not exceed 700 kg/h.

29 June 2018 in Mordovia University Bulletin
Verified
Journal Article
Open access
VUVavilov Saratov State Agrarian University
Vavilov Saratov State Agrarian University
FRF. Ya. Rudik
F. Ya. Rudik
BZB. P. Zagorodskih
B. P. Zagorodskih
NMN. L. Morgunova
N. L. Morgunova
YKYu. A. Kodatsky
Yu. A. Kodatsky
PFPitko F F
Pitko F F
Официальный сайт журнала "Вестник Мордовского университета"

28 November 2018 in Mordovia University Bulletin
Verified
Journal Article
Open access
AAAlexander V. Anisimov
Alexander V. Anisimov
FRFelix Ya. Rudik
Felix Ya. Rudik
BZBoris P. Zagorodskih
Boris P. Zagorodskih
Introduction. In small enterprises with simplified technological process of graded milling, preparations, which involve cleaning, peeling and moistening grain, play an essential role for ensuaring high quality of graded flour. Modern equipment for the low-productive mills implies only dry cleaning of grains in an abrasive machine with their further cold conditioning. The equipment designed for graded milling with deep multiple cleaning, washing and hydrothermal treatment is not possible. It significantly increases the cost of flour. The aim of the study is to increase both qualitative and quantitative indicators of graded flour in small enterprises through peeling and drying of grains before milling. Materials and Methods. The quality analyses of grain processing according to such indicators as ash content (whiteness), moisture, quantity of fractured grains were carried out according to State Standards of the Russian Federation and the methods established in science and practice. The degree of peeling was determined by the whiteness indicator with a photoelectric whitener SKIB-M (GOST 26361-2013 “Flour. Test method for whiteness”). Grain moisture was determined according to GOST 13586.5-2015 by the drying cabinet DEC-3M (drying electrical cabinet, model type 3M). The number of fractured grains was determined according to GOST 30483-97. Results. The research result revealed the dependence of grain processing on the technical aids. А combined peeling–drying machine was developed on this principle. The authors have developed rational operations of grain processing, which increase the whiteness of the received flour on average 4–7 conventional units. The standard instrument for whiteness definition has been studied and set. According to the given results optimal operating parameters for grain processing before milling have been developed: machine productivity (Q = 700 kg/h); the period of grain processing (t = 72 s.); optimum moisture content (from the point of view of obtained flour whiteness) of grains received for milling (W = 14 %); radiant power (P = 1 000 W). Conclusions. The research proved the fact that peeling of grains is one of the most effective ways of increasing the grade of end products of small enterprises with simplified technological process of graded milling. The efficiency of peeling seeds of wheat with humidity higher than 16 % decreases that speaks for the need to dry grains. The authors of the article introduce the equipment and technology for grain processing before graded milling, which provide grain peeling and, if necessary, drying. The operating parameters of the peeling-drying machine for preparation of grains for milling have been determined. The developed technology provide, if necessary, drying the remoistened grain to necessary standards that gives the chance to produce high-quality flour from the grains processed hydrothermally without processing moisture conditions required. The machine productivity in the mode of drying should be connected with the power of microwave infrared radiation, and its time and power should be limited to a maximum permissible grain temperature, which does not exceed 60 ºС. Keywords: peeling, whiteness, moisture, drying, preparation of grain for grinding For citation: Anisimov A. V., Rudik F. Ya., Zagorodskih B. P. Technological Improvements of Grain Preparation for Milling in Small Enterprises. Vestnik Mordovskogo universiteta = Mordovia University Bulletin. 2018; 28(4):603–623. DOI: https://doi.org/10.15507/0236-2910.028.201804.603-623 Acknowledgments: The study was conducted as part of an agreement with the Foundation for Assistance to Development of Small Enterprises in Scientific and Technical Sphere (No. 180GS1 / 6784, 25 December 2014) under the “START-1” program together with “Healthy Food” LLC.

22 August 2025 in Bulletin of KSAU
Verified
Journal Article
Open access
PDF file
OFOlga Fomenko
Olga Fomenko
ASAyazhan Sagingalieva
Ayazhan Sagingalieva
NMNatalya Morgunova
Natalya Morgunova
FRFelix Rudik
Felix Rudik
The aim of the study is to investigate and substantiate thermophysical processes in the production of liquid packaged fast-food broths with a long shelf life. The heat capacity of water decreased when heated from 0 to 37 °C, with further heating it increased, but insignificantly in its absolute value. This circumstance allowed us to conclude that it is possible to use preheated water to 70 °C outside the digester. This significantly reduces the negative impact of prolonged exposure to high temperatures on mass transfer processes. It was experimentally established that an increase in the water heating temperature in the range from 80 to 100 °C increases the thermal conductivity index by only 6 %, and then it remains virtually unchanged. The intensity of heat transfer from hotter to colder layers of water as a result of thermal interaction of water molecules acquires a linear pattern. This does not increase the intensity of mass transfer processes and, accordingly, does not increase the efficiency of heat transfer in meat and bone raw materials. Along with the water heating temperature, one of the key factors influencing the heating rate of meat and bone raw materials during cooking is the heating duration. It depends on the volume of pieces of meat and bone, as well as on the individual surface areas of bodies. As a result, knowing and taking into account the influence of thermophysical characteristics on the process of heating meat and bone raw materials with a heat carrier, it is possible to effectively control the process of cooking broth. In technological terms, this pattern allows improving the quality of products, increasing the productivity of the flow-technological line and optimizing energy costs for hydrothermal processes, ensuring the production of finished products with high consumer characteristics.

1 February 2022 in IOP Conference Series: Earth and Environmental Science
Verified
Conference Paper
Open access
NMN L Morgunova
N L Morgunova
FRF Y Rudik
F Y Rudik
OFO S Fomenko
O S Fomenko
ZIZ I Ivanova
Z I Ivanova
DMDmitriy Makarov
Dmitriy Makarov
ESE A Sundukov
E A Sundukov
The article deals with the issues related to the process of grain processing to accelerate the process of wetting during simple grinding into wallpaper flour and decontamination of grain during storage with ultrasonic intensification of the process. A mathematical simulation of the grain processing process was carried out using the Statistica.10 program. The optimal operating parameters of the preparation of wheat grain for simple grinding were selected: water temperature – 300C, processing time – 40 seconds, the frequency of ultrasonic vibrations – 18-18.2 kHz, the intensity of the ultrasonic field – no more than 1 W/cm2.