Michal Sovcik

Michal Sovcik

Auto-generated profile, based on publicly available information

Michal Sovcik

Department of IC Design and Test, Institute of Electronics and Photonics, Faculty of Electrical Engineering and Information Technology, Slovak University of Technology, Ilkovicova 3, 841 04 Bratislava, Slovakia

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
25 August 2021 in Sensors
Verified
Journal Article
Open access
PDF file
MPMiroslav Potocny
Miroslav Potocny
MKMartin Kováč
Martin Kováč
DADaniel Arbet
Daniel Arbet
MSMichal Sovcik
Michal Sovcik
LNLukas Nagy
Lukas Nagy
RRRichard Ravasz
Richard Ravasz
The power saving issue and clean energy harvesting for wireless and cost-affordable electronics (e.g., IoT applications, sensor nodes or medical implants), have recently become attractive research topics. With this in mind, the paper addresses one of the most important parts of the energy conversion system chain – the power management unit. The core of such a unit will be formed by an inductorless, low-voltage DC-DC converter based on the cross-coupled dynamic-threshold charge pump topology. The charge pump utilizes a power-efficient ON/OFF regulation feedback loop, specially designed for strict low-voltage start-up conditions by a driver booster. Taken together, they serve as the masters to control the charge pump output (up to 600 mV), depending on the voltage value produced by a renewable energy source available in the environment. The low-power feature is also ensured by a careful design of the hysteresis-based bulk-driven comparator and fully integrated switched-capacitor voltage divider, omitting the static power consumption. The presented converter can also employ the on-chip RF-based energy harvester for use in a wireless power transfer system.

1 January 2018 in Microelectronics Reliability
Verified
Journal Article
Closed access
MŠMichal Šovčík
Michal Šovčík
MKMartin Kováč
Martin Kováč
DADaniel Arbet
Daniel Arbet
VSViera Stopjaková
Viera Stopjaková
MPMiroslav Potocny
Miroslav Potocny

11 November 2023 in Electronics
Verified
Journal Article
Open access
PDF file
DMDavid Maljar
David Maljar
MSMichal Sovcik
Michal Sovcik
MPMiroslav Potocny
Miroslav Potocny
RORóbert Ondica
Róbert Ondica
DADaniel Arbet
Daniel Arbet
VSViera Stopjaková
Viera Stopjaková
This article deals with the calibration method of analog integrated circuits (ICs) designed in CMOS nanotechnology. A brief analysis of various methods and techniques (e.g., fuse trimming, chopper stabilization, auto-zero technique, etc.) for calibration of a specific IC’s parameter is given, leading to motivation for this research that is focused on the digital calibration. Then, the principle and overall design of the calibration subcircuit, which was generally used to calibrate the input offset voltage VIN_OFF of the operational amplifier (OPAMP). The essence of this work is verification of the proposed digital calibration algorithm for minimization the VIN_OFF of a bulk-driven fully differential difference amplifier (FDDA) with the power supply voltage VDD = 0.4 V. Evaluation of ASIC prototyped chip samples with silicon-proved results has been done. This evaluation contains comparison of selected parameters and characteristics obtained from both simulations and measurements of non-calibrated and calibrated FDDA configurations.

1 April 2018
Verified
Conference Paper
Closed access
MSMichal Sovcik
Michal Sovcik
VSViera Stopjaková
Viera Stopjaková
DADaniel Arbet
Daniel Arbet
MKMartin Kovac
Martin Kovac
MPMiroslav Potocny
Miroslav Potocny
This paper presents the analysis of digital calibration adverse effects, that arise from the connection of the calibration circuit to an operational amplifier being the circuit under calibration. In this way, the amplifier transfer function is affected and so are the frequency characteristics. Principles of the proposed calibration method are described. The calibration system was implemented in 130 nm CMOS technology node. In order to estimate arising adverse effects of calibration hardware on the amplifier performance, the small-signal analysis was performed. The detailed simulation results revealed the worst-case reduction of the VGA bandwidth to 87% and reduction of the gain-bandwidth to 75% with the calibration circuit connected. In the simulation analysis carried out, also mismatch, process parameters fluctuations and temperature variations have been considered.

1 October 2017
Verified
Conference Paper
Closed access
MSMichal Sovcik
Michal Sovcik
VSViera Stopjaková
Viera Stopjaková
DADaniel Arbet
Daniel Arbet
MKMartin Kovac
Martin Kovac
MPMiroslav Potocny
Miroslav Potocny
This work deals with the influence of increasing rate of integration (i.e. technology downscale) on the main parameters of integrated circuits. Our concerns are focused on calibration methods of analog integrated circuits that can compensate undesired side effects of technology downscale. The paper describes both the general principle of calibration system as well as design requirements for main blocks of the calibration subcircuit. Then, the approach for calibration employment in operational amplifiers is described, where the voltage offset cancellation is of the main concern. Consequently, a specific application of previously described calibration fundamentals is presented. For this purpose, statistical results on the input offset voltage of the operational amplifier are used, where the operational amplifier is realized in 130 nm CMOS technology.

16 June 2021
Verified
Book Chapter
Open access
PDF file
MSMichal Sovcik
Michal Sovcik
LNLukas Nagy
Lukas Nagy
VSViera Stopjaková
Viera Stopjaková
DADaniel Arbet
Daniel Arbet
This chapter deals with digital method of calibration for analog integrated circuits as a means of extending its lifetime and reliability, which consequently affects the reliability the analog electronic system as a whole. The proposed method can compensate for drift in circuit’s electrical parameters, which occurs either in a long term due to aging and electrical stress or it is rather more acute, being caused by process, voltage and temperature variations. The chapter reveals the implementation of ultra-low voltage on-chip system of digitally calibrated variable-gain amplifier (VGA), fabricated in CMOS 130 nm technology. It operates reliably under supply voltage of 600mV with 10% variation, in temperature range from −20°C to 85°C. Simulations suggest that the system will preserve its parameters for at least 10 years of operation. Experimental verification over 10 packaged integrated circuit (IC) samples shows the input offset voltage of VGA is suppressed in range of 13μV to 167μV. With calibration the VGA closely meets its nominally designed essential specifications as voltage gain or bandwidth. Digital calibration is comprehensively compared to its widely used alternative, Chopper stabilization through its implementation for the same VGA.