Tatsuo Tabaru

Tatsuo Tabaru

Auto-generated profile, based on publicly available information

Tatsuo Tabaru

Sensing System Research Center, National Institute of Advanced Industrial Science and Technology 2 , 807-1 Shuku-machi, Tosu, Saga 841-0052, Japan

Research Focus & Metrics

Academic Career Length

31Years (1996-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 1998 in Intermetallics
Verified
Journal Article
Closed access
SSSatoshi Semboshi
Satoshi Semboshi
TTTatsuo Tabaru
Tatsuo Tabaru
Hideki HosodaHideki Hosoda
Hideki Hosoda
SHShuji Hanada
Shuji Hanada

17 October 2019 in Thin Solid Films
Verified
Journal Article
Closed access
TTTatsuo Tabaru
Tatsuo Tabaru
MAMorito Akiyama
Morito Akiyama

1 May 2017 in AIP Advances
Verified
Journal Article
Open access
PDF file
TSTakashi Sumiyama
Takashi Sumiyama
TFTakaya Fukumoto
Takaya Fukumoto
YOYasunori Ohtsu
Yasunori Ohtsu
TTTatsuo Tabaru
Tatsuo Tabaru
Spatial structure of high-density radio frequency ring-shaped magnetized discharge plasma sputtering with two facing ZnO/Al2O3 cylindrical targets mounted in ring-shaped hollow cathode has been measured and Al-doped ZnO (AZO) thin film is deposited without substrate heating. The plasma density has a peak at ring-shaped hollow trench near the cathode. The radial profile becomes uniform with increasing the distance from the target cathode. A low ion current flowing to the substrate of 0.19 mA/cm2 is attained. Large area AZO films with a resistivity of 4.1 – 6.7×10-4 Ω cm can be prepared at a substrate room temperature. The transmittance is 84.5 % in a visible region. The surface roughnesses of AZO films are 0.86, 0.68, 0.64, 1.7 nm at radial positions of r = 0, 15, 30, 40 mm, respectively, while diffraction peak of AZO films is 34.26°. The grains exhibit a preferential orientation along (002) axis.

1 June 2006 in Japanese Journal of Applied Physics
Verified
Journal Article
Closed access
IOIchiro Ohshima
Ichiro Ohshima
MAMorito Akiyama
Morito Akiyama
AKAkira Kakami
Akira Kakami
TTTatsuo Tabaru
Tatsuo Tabaru
TKToshihiro Kamohara
Toshihiro Kamohara
HNHiroaki Noma
Hiroaki Noma

1 February 2023 in AIP Advances
Verified
Journal Article
Open access
PDF file
TMTaisei Motomura
Taisei Motomura
KTKenshin Takemura
Kenshin Takemura
TNToshimi Nagase
Toshimi Nagase
NMNobutomo Morita
Nobutomo Morita
TTTatsuo Tabaru
Tatsuo Tabaru
Magnetron sputtering generally increases the temperature of the substrate placed to face the sputtering target above 40 °C because the plasmas are transported through unbalanced magnetic field lines from the sputtering target to the substrate surface. However, by using a magnetic mirror-type magnetron cathode, we were able to suppress the temperature of the substrate temperature to the environmental temperature of less than 40 °C at a target–substrate distance of ≥ 50 mm with a DC input power of ≤ 30 W and an Ar gas pressure of ≤ 0.15 Pa. This was possible because the balanced magnetic field lines confined the plasmas near the sputtering target. By enabling film deposition on low heat-resistant substrates, this deposition technique for suppressing the substrate temperature may have uses in various application fields.

1 December 2017 in AIP Advances
Verified
Journal Article
Open access
TMTaisei Motomura
Taisei Motomura
TTT. Tabaru
T. Tabaru
A novel magnetron sputtering cathode with a magnetic mirror configuration is proposed, for low power density operation. The magnetic field profiles are simply constructed using two cylindrical permanent magnets positioned behind the disk-shaped sputtering target of 50 mm in diameter. The magnetic mirror configuration near the center and the outer edges of the target enables low power density operation up to 0.25 W/cm2 in the case of DC input power of 5 W. A sputtering rate of ∼0.2 nm/min was obtained under experimental conditions with target-substrate distance of 280 mm, Ar gas pressure of 0.1 Pa, and DC input power of 15 W.