The 2022 revision of Aotearoa New Zealand National Seismic Hazard Model (NZ NSHM 2022) has involved significant revision of all datasets and model components. In this article, we present a subset of many results from the model as well as an overview of the governance, scientific, and review processes followed by the NZ NSHM team. The calculated hazard from the NZ NSHM 2022 has increased for most of New Zealand when compared with the previous models. The NZ NSHM 2022 models and results are available online.
15 November 2023 in Seismological Research Letters
This article presents the development of the site characterization database for the 2022 New Zealand National Seismic Hazard Model update. This database summarizes the site characterization parameters at past and present GeoNet seismic monitoring network instrument locations, including strong‐motion, short‐period, and broadband seismometer stations. Site characterization parameters required to assess and improve empirical ground‐motion models and those used in codified seismic design frameworks internationally have been included in the database. Measurement uncertainty was assigned, and the quality of the data used to assign each parameter was classified. The site period ( ) was the most well constrained of all the site parameters, with almost half of the database classified based on high‐quality measurements, with these dominated by microtremor‐based horizontal‐to‐vertical spectral ratio. Although there was an improvement in the quality of the parameters representing the time‐averaged shear‐wave velocity in the uppermost 30 m of the profile ( ), little site‐specific data were available, with almost no information for rock sites. Most of these classifications were based on national maps or geologic interpretation. Depth‐based parameters ( and ) had the lowest quality overall, with very few direct measurements available to constrain these values. Despite these limitations, the quality of parameters assigned to instrument locations has improved and greatly expanded previous databases through the assignment of parameter values to the entire GeoNet seismic network.
The direct-push crosshole (DPCH) test is a new, invasive, near-surface seismic testing method. DPCH combines the desirable characteristics of borehole-based crosshole seismic testing with the relative inexpensiveness and speed of direct-push testing methods like cone penetration testing (CPT). At each measurement depth (typically every 20–50 cm), compression (P) and shear (S) waves are generated simultaneously using hammer taps on one of the CPT push rods (a pushable, in-ground seismic source can also be used). These P- and S-waves are propagated between two instrumented seismic cones (i.e., a source and receiver cone). The instrumented cones contain a sensor package with three orthogonally oriented geophones to measure the seismic waveforms and a MEMS accelerometer to track the deviation/position of each cone as it is advanced into the ground. DPCH testing enables high-resolution profiles of P- and S-wave velocity to be measured over the top 20–30 meters of the subsurface for use in geotechnical engineering analyses. It also allows for testing across/through ground improvement elements like stone columns. The DPCH instrumentation, testing methodology, and data reduction techniques are explained in detail in this article, and results from several sites are discussed.
1 November 2021 in Journal of Geotechnical and Geoenvironmental Engineering
Using a database of approximately 900 data pairs from 230 sites of co-located cone penetration test (CPT) soundings and boreholes with standard penetration tests (SPT) in the South Island of New Zealand, this paper assesses the applicability of a range of existing SPT–CPT correlations. Simple linear SPT–CPT correlations for different soil types as well as correlations based on the soil behavior type index ( ) from CPT data were assessed. The measured SPT data were poorly fit by all the correlations, with under- and over-predictions greater than 50% for between 40% and 55% of the database. The 95% confidence interval of the bias between predicted and measured SPT values was large across all variables. The bias varied significantly as a function of CPT tip resistance and sleeve friction, with underestimates at low values dominated by fine-grained soils ( ), and overestimates at high values dominated by silty sand to dense sand ( ). There was no clear effect of the different drilling methods on the bias observed across all parameters. These results highlight the significant uncertainty involved in the application of these correlations in geotechnical design and assessments.
27 December 2023 in Bulletin of the Seismological Society of America
We provide an overview of the treatment of site effects in the New Zealand National Seismic Hazard Model (NZ NSHM), including a case study of basin effects in central Wellington. The NZ NSHM 2022 includes a change in site parameter from subsoil class (NZS class) to . Poor NZ characterization is a major source of uncertainty in the NSHM; however, advanced site characterization in Wellington allows for in‐depth study. First, we construct a regional 3D shear‐wave velocity model and maps of site parameters ( , NZS class, and ) for central Wellington. At central city soil sites, we find the ratios of NZ NSHM 2022 hazard spectra with respect to the current equivalent design spectra range from factors of ∼0.8–2.6 (median ∼1.5), depending on local site conditions and spectral period. Strong amplification peaks at 0.5–2 s are observed in central Wellington. Linear site‐specific amplifications from multiple methods are compared at 13 stations and are well‐defined by both site‐to‐site residuals and response spectral ratios relative to station POTS. At many deeper soft sites ( ), strong amplification peaks occur around that are underpredicted by mean ergodic ground‐motion model (GMM) predictions. This underprediction is slightly enhanced when using basin‐specific as an additional site parameter. Our study highlights outstanding challenges in modeling strong basin response within shallow basins in NSHMs, including the need to consider region‐ or basin‐specific modeling approaches as well as nonlinear effects at high shaking intensities that dominate the hazard. For New Zealand, in general, as illustrated in the Wellington case study, a priority is the further characterization of (and ) for the seismic network to better isolate and quantify uncertainties in seismic hazard and allow useful exploration of regional–GMM adjustments and partially nonergodic approaches.