Jagdeep Singh Sagu

Jagdeep Singh Sagu

Auto-generated profile, based on publicly available information

Jagdeep Singh Sagu

Loughborough University

Research Focus & Metrics

Academic Career Length

14Years (2013-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 August 2017 in Electrochimica Acta
Verified
Journal Article
Open access
JSJagdeep S. Sagu
Jagdeep S. Sagu
KWK.G.U. Wijayantha
K.G.U. Wijayantha
Asif TahirAsif Tahir
Asif Tahir
This is an open access article published by Elsevier and made available under the terms of the Creative Commons Attribution Licence (CC BY 4.0), https://creativecommons.org/licenses/by/4.0/. Supplementary data for this article is available in the Loughborough Data Repository at doi: 10.17028/rd.lboro.5568028Nanostructured Cobalt ferrite (CoFe2O4) thin films are fabricated by aerosol-assisted chemical vapour deposition (AACVD) and studied for application in supercapacitors. XRD and Raman spectroscopic analysis confirms the formation of single phase CoFe2O4. SEM analysis shows that the thin film morphology consists of nanoparticles less than 100 nm in size that are sintered together to form larger dendrites raised from the substrate. The larger dendrites range from 0.5 – 1 μm in diameter and are uniformly distributed over the FTO substrate, providing a highly porous structure which is desired for supercapacitor electrodes. Three-electrode electrochemical measurements reveal that CoFe2O4 is pseudocapacitive and is highly conducting. Studies of CoFe2O4 thin films in two-electrode symmetric supercapacitor configuration show a capacitance of 540 μF cm-2 and a relaxation time constant of 174 ms. Around 80% of the capacitance is retained after 7000 charge-discharge cycles when a maximum charging voltage of 1 V was used, indicating that the pseudocapacitive processes in CoFe2O4 are highly reversible and that it exhibits excellent chemical stability in 1 M NaOH alkaline electrolyte solution. The results show that CoFe2O4 is a cheap and promising alternative pseudocapacitive material to replace the expensive pseudocapacitive materials

7 January 2015 in Chemical Vapor Deposition
Verified
Journal Article
Open access
PDF file
PBPaul Brack
Paul Brack
JSJagdeep S. Sagu
Jagdeep S. Sagu
TPT. A. Nirmal Peiris
T. A. Nirmal Peiris
AMAndrew McInnes
Andrew McInnes
MSMauro Senili
Mauro Senili
ESElena Selli
Elena Selli
Thin film bismuth vanadate (BiVO4) photoelectrodes are prepared by aerosol‐assisted (AA)CVD for the first time on fluorine‐doped tin oxide (FTO) glass substrates. The BiVO4 photoelectrodes are characterised by X‐ray diffraction (XRD), Raman spectroscopy (RS), and energy‐dispersive X‐ray (EDX) spectroscopy and are found to consist of phase‐pure monoclinic BiVO4. Scanning electron microscopy (SEM) analysis shows that the thin film is uniform with a porous structure, and consists of particles approximately 75−125 nm in diameter. The photoelectrochemical (PEC) properties of the BiVO4 photoelectrodes are studied in aqueous 1 M Na2SO4 and show photocurrent densities of 0.4 mA cm−2, and a maximum incident‐photon‐to‐electron conversion efficiency (IPCE) of 19% at 1.23 V vs. the reversible hydrogen electrode (RHE). BiVO4 photoelectrodes prepared by this method are thus highly promising for use in PEC water‐splitting cells.

24 April 2017 in ACS Sustainable Chemistry & Engineering
Verified
Journal Article
Open access
DJD. S. Y. Jayathilake
D. S. Y. Jayathilake
TPT. A. Nirmal Peiris
T. A. Nirmal Peiris
JSJagdeep S. Sagu
Jagdeep S. Sagu
DPDominic B. Potter
Dominic B. Potter
KWK. G. U. Wijayantha
K. G. U. Wijayantha
DSD. J. Southee
D. J. Southee
This work reports the microwave-assisted fabrication of highly conducting Al-doped ZnO (AZO), Ga-doped ZnO (GZO), and Al, Ga codoped ZnO (AGZO) materials as cheaper earth abundant alternatives to indium tin oxide (ITO) for transparent conducting applications. All three doped ZnO powder samples were compressed into pellets, and their electrical properties were evaluated after the postsynthesis heat treatment. The heat treatment was performed by sintering the pellets at 600 °C in a reducing atmosphere using either conventional radiant annealing for 3 h or microwave annealing for 90 s. The Al and Ga dopant levels were systematically varied from 0.5 to 2.5 at. %, and it was found that the lowest resistivity values for the pelleted singly doped ZnO powders exist when the doping level is adjusted to 1.5 at. % for both AZO and GZO, giving resistivity values of 4.4 × 10–3 and 4.3 × 10–3 Ω·cm, respectively. The lowest resistivity of 5.6 × 10–4 Ω·cm was achieved for the pelleted codoped AGZO powder using the optimized Al and Ga dopant levels. Notably, this value is one magnitude lower than the best literature reported value for conventionally synthesized codoped AGZO powder. The resistivity values obtained for the pellets after radiant and microwave postsynthesis heat treatment are comparable, although the microwave heat treatment was performed only for 90 s, compared to 3 h for conventional radiant heat treatment. Hence, significant gains were made in the postannealing step by reducing time, cost, and energy required, benefiting our thrust for finding sustainable routes toward alternative low-cost transparent conducting oxides. As a proof of concept, transparent conducting thin films were fabricated via a simple aerosol-assisted deposition technique using our best conducting AGZO nanoparticles. The films exhibited a visible transmittance as good as 90% and a resistivity of 5.7 × 10–3 Ω·cm, which can compete with the existing high cost ITO films.

25 February 2016 in ACS Applied Materials & Interfaces
Verified
Journal Article
Open access
JSJagdeep Singh Sagu
Jagdeep Singh Sagu
KWK. G. Upul Wijayantha
K. G. Upul Wijayantha
MBMallika Bohm
Mallika Bohm
SBSiva Bohm
Siva Bohm
TRTapan Kumar Rout
Tapan Kumar Rout
Steel was anodized in 10 M NaOH to enhance its surface texture and internal surface area for application as an electrode in supercapacitors. A mechanism was proposed for the anodization process. Field emission gun scanning electron microscopy (FEGSEM) studies of anodized steel revealed that it contains a highly porous sponge like structure ideal for supercapacitor electrodes. X-ray photoelectron spectroscopy (XPS) measurements showed that the surface of the anodized steel was Fe2O3, while X-ray diffraction (XRD) measurements indicated that the bulk remained as metallic Fe. The supercapacitor performance of the anodized steel was tested in 1 M NaOH and a capacitance of 18 mF cm-2 was obtained. Cyclic voltammetry measurements showed that there was a large psueudocapacitive contribution which was due to oxidation of Fe to Fe(OH)2 and then further oxidation to FeOOH, and the respective reduction of these species back to metallic Fe. These redox processes were found to be remarkably reversible as the electrode showed no loss in capacitance after 1000 cycles. The results demonstrate that anodization of steel is a suitable method to produce high surface area electrodes for supercapacitors with excellent cycling lifetime.

19 November 2013 in Journal of Nanoparticle Research
Verified
Journal Article
Closed access
PDF file
TPT.A. Nirmal Peiris
T.A. Nirmal Peiris
HAHussain Alessa
Hussain Alessa
JSJagdeep S. Sagu
Jagdeep S. Sagu
IBIjaz Ahmad Bhatti
Ijaz Ahmad Bhatti
PIPatrick J. M. Isherwood
Patrick J. M. Isherwood
KWK.G.U. Wijayantha
K.G.U. Wijayantha

22 May 2014 in Journal of Solid State Electrochemistry
Verified
Journal Article
Closed access
PDF file
LMLucia Helena Mascaro
Lucia Helena Mascaro
APAdam Pockett
Adam Pockett
JMJohn M. Mitchels
John M. Mitchels
LPLaurence M. Peter
Laurence M. Peter
PCPetra J. Cameron
Petra J. Cameron
FMFrank Marken
Frank Marken