Z. Cedric Xia

Z. Cedric Xia

Auto-generated profile, based on publicly available information

Z. Cedric Xia

Ford Motor Company

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 December 2011 in Journal of Manufacturing Science and Engineering
Verified
Journal Article
Closed access
PDF file
RMRajiv Malhotra
Rajiv Malhotra
JCJian Cao
Jian Cao
FRFeng Ren
Feng Ren
VKVijitha Kiridena
Vijitha Kiridena
ZXZ. Cedric Xia
Z. Cedric Xia
NRN. V. Reddy
N. V. Reddy
Single point incremental forming (SPIF) is plagued by an unavoidable and unintended bending in the region of the sheet between the current tool position and the fixture. The effect is a deformation of the region of the sheet in between the formed area and the fixture as well as deformation of the already formed portion of the wall, leading to significant geometric inaccuracy in SPIF. Double sided incremental forming (DSIF) uses two tools, one on each side of the sheet to form the sheet into the desired shape. This work explores the capabilities of DSIF in terms of improving the geometric accuracy as compared to SPIF by using a novel toolpath strategy in which the sheet is locally squeezed between the two tools. Experiments and simulations are performed to show that this strategy can improve the geometric accuracy of the component significantly by causing the deformation to be stabilized into a local region around the contact point of the forming tool. At the same time an examination of the forming forces indicates that after a certain amount of deformation by using this strategy a loss of contact occurs between the bottom tool and the sheet. The effects of this loss of contact of the bottom tool on the geometric accuracy and potential strategies, in order to avoid this loss of contact, are also discussed.

4 September 2015 in Journal of Manufacturing Science and Engineering
Verified
Journal Article
Open access
PDF file
ZZZixuan Zhang
Zixuan Zhang
HRHuaqing Ren
Huaqing Ren
RXRui Xu
Rui Xu
NMNewell Moser
Newell Moser
JSJacob Smith
Jacob Smith
JCJian Cao
Jian Cao
Double-sided incremental forming (DSIF) is a relatively new dieless forming process which uses two hemispherical ended tools, one on each side of the sheet, moving along a predefined trajectory to locally deform a peripherally clamped sheet of metal. DSIF provides greater process flexibility, higher formability, and eliminates the tooling cost when compared to conventional sheet forming processes. While DSIF provides much improved geometric accuracy compared to other incremental forming processes, current toolpath planning strategies suffer from long forming times. A novel mixed double-sided incremental forming (MDSIF) toolpath strategy is proposed in the present study. It simultaneously reduces the total forming time by half while preserving the best currently achievable geometric accuracy. The effect of the forming parameters, i.e., of the incremental depth and of tool positioning on the geometric accuracy of the parts formed with MDSIF was investigated and compared to those formed by traditional DSIF strategies.

8 May 2013 in Journal of Engineering Materials and Technology
Verified
Journal Article
Closed access
PDF file
JHJi He
Ji He
ZXZ. Cedric Xia
Z. Cedric Xia
DZDanielle Zeng
Danielle Zeng
SLShuhui Li
Shuhui Li
Forming limit diagrams (FLD) have been widely used as a powerful tool for predicting sheet metal forming failure in the industry. The common assumption for forming limits is that the deformation is limited to in-plane loading and through-thickness bending effects are negligible. In practical sheet metal applications, however, a sheet metal blank normally undergoes a combination of stretching, bending, and unbending, so the deformation is invariably three-dimensional. To understand the localized necking phenomenon under this condition, a new extended Marciniak–Kuczynski (M–K) model is proposed in this paper, which combines the FLD theoretical model with finite element analysis to predict the forming limits after a sheet metal undergoes under continuous-bending-under-tension (CBT) loading. In this hybrid approach, a finite element model is constructed to simulate the CBT process. The deformation variables after the sheet metal reaches steady state are then extracted from the simulation. They are carried over as the initial condition of the extended M–K analysis for forming limit predictions. The obtained results from proposed model are compared with experimental data from Yoshida et al. (2005, “Fracture Limits of Sheet Metals Under Stretch Bending,” Int. J. Mech. Sci., 47(12), pp. 1885–1986) under plane strain deformation mode and the Hutchinson and Neale's (1978(a), “Sheet Necking—II: Time-Independent Behavior,” Mech. Sheet Metal Forming, pp. 127–150) M–K model under in-plane deformation assumption. Several cases are studied, and the results under the CBT loading condition show that the forming limits of post-die-entry material largely depends on the strain, stress, and hardening distributions through the thickness direction. Reduced forming limits are observed for small die radius case. Furthermore, the proposed M–K analysis provides a new understanding of the FLD after this complex bending-unbending-stretching loading condition, which also can be used to evaluate the real process design of sheet metal stamping, especially when the ratio of die entry radii to the metal thickness becomes small.

17 July 2013 in Journal of Manufacturing Science and Engineering
Verified
Journal Article
Closed access
PDF file
JHJi He
Ji He
ZXZ. Cedric Xia
Z. Cedric Xia
SLShuhui Li
Shuhui Li
DZDanielle Zeng
Danielle Zeng
Since the forming limit diagram (FLD) was introduced by Keeler, etc., five decades ago, it has been intensively studied by researchers and engineers. Most work has focused on the in-plane deformation which is considered as the dominant mode of the majority forming processes. However the effect of out-of-plane deformation becomes important in the accurate prediction of formability when thick sheet metals and/or smaller forming radii are encountered. Recent research on the stretch-bending induced FLD (BFLD) has been inconclusive. Some studies indicated that the bending effect will enhance a sheet metal's formability while others suggested otherwise. In this paper, we present an in-depth study of the through-thickness bending effect on the forming limits. The Marciniak–Kuczynski (M–K) analysis is extended to include bending, and models based on both flow theory and deformation theory of plasticity are proposed. The study is limited to the right-hand-side of FLD where the bending is along the major stretch direction. The radial return method is adopted as the framework to integrate constitutive equations. The results show that the bending process decreases the sheet metal formability with the flow-theory based model, while the opposite is true if the deformation theory based analysis is adopted. A detailed examination of the deformation histories from those two models reveals that the loading–unloading-reverse loading process during stretch-bending holds the key to the understanding of the conflicting results. The insight gained from the proposed FLD prediction model in this paper provides a new understanding of how the bending process affects the FLD, which can be used to predict and explain the localized necking phenomenon under the stretch-bending condition.

1 January 2008
Verified
Conference Paper
Closed access
PDF file
ZXZ. Cedric Xia
Z. Cedric Xia
DZDanielle Zeng
Danielle Zeng
The Forming Limit Diagram (FLD) as developed by Keeler etc. has been widely used to assess sheet metal failure during a variety of forming operations. Its theoretical and empirical foundation is based on localized necking under biaxial loading for the sheet metal. While the in-plane deformation is generally the dominant mode for most forming operations, sheet metal bending is inevitably coupled to the deformation process, and the traditional Forming Limit Diagram has to be modified to take into account the bending effect, especially when the bending radius becomes smaller. This paper presents a theoretical formulation for the Bending-Enhanced Forming Limit model. The deformation theory of plasticity is employed for the instability analysis, and the bending is assumed only in the direction along one principal loading. The obtained results show that the forming limit is enhanced by the bending effect, consistent with experimental observations.

13 April 2007 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
PDF file
DZDanielle Zeng
Danielle Zeng
ZXZ. Cedric Xia
Z. Cedric Xia