18 May 2012 in Advanced Energy Materials
16 February 2011 in Energy & Environmental Science
Lithium iron phosphate olivine (LFP) and lithium manganese oxide spinel (LMO) are competitive and complementary to each other as cathode materials for lithium ion batteries, especially for use in hybrid electric vehicles and electric vehicles. Interest in these materials, due to their low cost and high safety, has pushed research and development forward and toward high performance in terms of rate capability and capacity retention or cyclability at a high temperature of around 60 °C. From the view point of basic properties, LFP shows a higher gravimetric capacity while LMO has better conductivities, both electrically and ionically. According to our comparison experiments, depending on the material properties and operational potential window, LFP was favored for fast charging while LMO led to better discharge performances. Capacity fading at high temperatures due to metal dissolution was revealed to be the most problematic issue of LFP and LMO-based cells for electric vehicles (EVs), with thicker electrodes, in the case of no additives in the electrolyte and no coating to prevent metal dissolution on cathode materials. Various strategies to enhance the properties of LFP and LMO are ready for the realization of EVs in the near future.
2 November 2018 in Advanced Materials
4 April 2012 in Energy & Environmental Science
A facile approach to the surface modification of spinel LiNi0.5Mn1.5O4 (LNMO) cathode active materials for high-voltage lithium ion batteries is demonstrated. This strategy is based on nanoarchitectured polyimide (PI) gel polymer electrolyte (GPE) coating. The PI coating layer successfully wrapped a large area of the LNMO surface via thermal imidization of 4-component (pyromellitic dianhydride/biphenyl dianhydride/phenylenediamine/oxydianiline) polyamic acid. In comparison to conventional metal oxide-based coatings, distinctive features of the unusual PI wrapping layer are the highly continuous surface coverage with nanometre thickness (∼10 nm) and the provision of facile ion transport. The nanostructure-tuned PI wrapping layer served as an ion-conductive protection skin to suppress the undesired interfacial side reactions, effectively preventing the direct exposure of the LNMO surface to liquid electrolyte. As a result, the PI wrapping layer played a crucial role in improving the high-voltage cell performance and alleviating the interfacial exothermic reaction between charged LNMO and liquid electrolyte. Notably, the superior cycle performance (at 55 °C) of the PI-wrapped LNMO (PI-LNMO) was elucidated in great detail by quantitatively analyzing manganese (Mn) dissolution, cell impedance, and chemical composition (specifically, lithium fluoride (LiF)) of byproducts formed on the LNMO surface.
5 August 2011 in Energy & Environmental Science
Succinonitrile (SN, CN–[CH2]2–CN) is evaluated as an additive for improving thermal stability in ethylene carbonate (EC)-based electrolytes for lithium ion batteries. Without any sacrifice of performance such as cyclability and capacity, the introduction of SN into an electrolyte with a graphite anode and LixCoO2 cathode leads to (1) reducing the amount of gas emitted at high temperature, (2) increasing the onset temperature of exothermic reactions and (3) decreasing the amount of exothermal heat. The improvement in the thermal stability is considered to be due to strong complex formation between the surface metal atoms of LixCoO2 and nitrile (–CN) groups of SN, from spectroscopic studies based on photoelectrons induced by X-rays and by considering that the exothermic heat and gas evolution are caused by interfacial reactions between the electrolyte and cathode.
14 April 2014 in Journal of Materials Chemistry A
Lithium ion transport was accelerated within graphite by controlling its d-spacing as well as its functional groups. By oxidizing bare graphite under a mild condition, expanded graphites (EG* where * = functional groups) were obtained with increasing d-spacing from 0.3359 nm to 0.3395 nm as well as with functional groups formed on the plane or at the edges of graphites. The subsequent thermal reduction of EG* led to an insignificant change of d-spacing (0.3390 nm), simultaneously eliminating a portion of the functional groups (EG). The enlargement of d-spacing reduced kinetic hindrance of lithium ion movement within the expanded graphites (EG* and EG) by reserving more space for the ionic transport route. In addition, the activation energy of lithium ion intercalation in EG* was reduced by surface charge polarization of graphites induced by hydrogen bonds between oxygen atoms of carbonates in electrolytes and hydrogen atoms of surface functional groups of the expanded graphites, even if the degree of graphitization decreased. Re-graphitization induced by the subsequent thermal reduction increased delithiation capacities (QdLi) of EG as an anode for lithium ion batteries especially at high currents: QdLi at 50 C = 243 mA h g−1 for EG versus 66 mA h g−1 for bare graphite.