21 September 2023 in Optics Express
Large aperture ground-based segmented telescopes typically use electrical edge sensors to detect co-phase errors. However, complex observing environments can lead to zero-point drift of the edge sensors, making it challenging to maintain the long-term co-phase of the segmented primary mirror using only edge sensors. Therefore, employing optical piston error detection methods for short-term calibration of edge sensors can address the issue of zero-point drift in the sensors. However, atmospheric turbulence can affect calibration accuracy based on the observational target. To achieve high-precision calibration of electrical edge sensors, this study investigates the impact of atmospheric turbulence on optical piston error detection. Based on simulated results, it is found that the actual measured piston error in the presence of atmospheric turbulence is the difference between the average phases of the two segments. Subsequently, optical piston error detection experiments were conducted in a segmented mirror system under simulated turbulent conditions with varying turbulence intensities. Experimental studies have shown that the detection accuracy of the optical method is almost the same as without turbulence when using a detection aperture size that is 0.82 times the atmospheric coherence length and an exposure time of at least 40 ms. The root mean square of the cross-calibration is better than 3 nm. These experimental results indicate that under conditions of good atmospheric seeing, the optical piston error detection method can meet the short-term calibration requirements of edge sensors by setting reasonable detection area size and exposure time. It may even be possible to directly use optical detection methods to replace edge sensors for real-time detection of piston errors.
2 April 2024 in Optics Express
For segmented telescopes, achieving fine co-focus adjustment is essential for realizing co-phase adjustment and maintenance, which involves adjusting the millimeter-scale piston between segments to fall within the capture range of the co-phase detection system. CGST proposes using a SHWFS for piston detection during the co-focus adjustment stage. However, the residual piston after adjustment exceeds the capture range of the broadband PSF phasing algorithm( ± 30μm), and the multi-wavelength PSF algorithm requires even higher precision in co-focus adjustment. To improve the co-focus adjustment accuracy of CGST, a fine co-focus adjustment based on cross-calibration is proposed. This method utilizes a high-precision detector to calibrate and fit the measurements from the SHWFS, thereby reducing the impact of atmospheric turbulence and systematic errors on piston measurement accuracy during co-focus adjustment. Simulation results using CGST demonstrate that the proposed method significantly enhances adjustment accuracy compared to the SHWFS detection method. Additionally, the residual piston after fine co-focus adjustment using this method falls within the capture range of the multi-wavelength PSF algorithm. To verify the feasibility of this method, experiments were conducted on an 800mm ring segmented mirror system, successfully achieving fine co-focus adjustment where the remaining piston of all segments fell within ±15μm.
23 May 2025 in Optics Express
Optical interference phase measurement is a crucial technology for measuring the edge height of segments during the co-phased adjustment stage of giant astronomical telescopes equipped with segmented primary mirrors. For the Chinese Giant Solar Telescope (CGST), achieving optical interferometric measurements with a range of 10 µm or more is a critical challenge that must be addressed to integrate the the co-focus and phasing adjustment processes. Given the unique requirements of solar observation, CGST intends to implement multi-wavelength technology to tackle the measurement range issue. However, this multi-wavelength measurement approach encounters the problem of edge jumps, and merely extending the exposure time does not effectively resolve this issue, which could compromise the telescope’s diffraction-limited observational capabilities. The study indicates that the relative measurement error between two wavelengths, caused by atmospheric turbulence, is the primary factor leading to edge jumps. To address this issue, the paper proposes a dual-wavelength synchronous measurement technique. An experiment conducted on a segmented-mirror system demonstrates that, under turbulent conditions and with an exposure time of one second, the probability of edge jumps is negligible. By employing dual-wavelength synchronous technology, each measurement and adjustment takes only a few seconds, allowing the co-phased adjustment of CGST to be completed in just two to three rounds of measurement and adjustment.
10 June 2025 in Optics Express
For ground-based segmented telescopes, the active control system primarily adjusts three out-of-plane DOFs: tip, tilt, and piston. In contrast, in-plane DOFs rely on high-precision mechanical alignment. A systematic analysis of the effects of in-plane motion on the optical performance of ring segmented mirror systems is presented, and an analytical relationship between in-plane motion and the higher-order residual aberrations after tilt compensation is derived. Conventional alignment techniques based on three-dimensional metrology do not provide the necessary in-plane motion detection accuracy required for the CGST, which operates in the visible spectrum and demands higher surface precision than infrared telescopes. Previous measurements using laser trackers indicate that the achievable accuracy is insufficient for CGST alignment. A method based on wavefront aberration has been proposed to enhance the accuracy of in-plane motion measurements and alignments. This approach establishes a correlation between wavefront aberrations and in-plane motion. Wavefronts are obtained through phase retrieval and fitted using orthogonal Zernike polynomials to develop the mapping model. During the alignment process, the effect induced by Clocking is compensated by adjusting DX. Simulations using parameters from the CGST show that, with a point spread function image SNR above 20 dB, the residual wavefront aberration after compensation meets the diffraction-limited requirements in the visible range. The results confirm the potential of this method for achieving high-precision in-plane DOFs alignment in segmented solar telescopes.
16 September 2026 in Optics Express
High-quality multi-band observation data are crucial for accurately extracting physical information about the solar atmosphere, such as the velocity field and the magnetic field. Due to the effect of atmospheric turbulence, observation data acquired by ground-based solar telescopes are severely distorted and require high-resolution reconstruction. Compared with independent reconstruction for each band, the existing multi-band synchronous reconstruction method provides higher reconstruction consistency and efficiency. However, this method relies on the assumption of cross-wavelength wavefront consistency. Atmospheric dispersion violates this assumption with increasing zenith angle, thereby introducing cross-wavelength wavefront errors. We analyze the effect of cross-wavelength wavefront errors on the modulus and phase of multi-band synchronous reconstruction, respectively. The results show that cross-wavelength wavefront errors have only a small effect on phase reconstruction, while the modulus gradually attenuates with increasing zenith angle. Based on the different sensitivities of modulus and phase to cross-wavelength wavefront errors, we propose a multi-band synchronous reconstruction method with decoupled modulus and phase. The phase is extracted from existing synchronous reconstruction results, while the modulus is independently reconstructed using speckle interferometry. This avoids the effect of cross-wavelength wavefront errors on modulus reconstruction. Multi-band high-resolution reconstruction results are then obtained from the reconstructed modulus and extracted phase. Ground-based simulated data and three sets of New Vacuum Solar Telescope (NVST) synchronous observation data are used for testing. The test results show that our method can effectively mitigate the degradation of synchronous reconstruction caused by cross-wavelength wavefront errors. This enables synchronous reconstruction to maintain efficient and consistent performance even at high zenith angles.
5 November 2025 in Optics Express
The phase of a plane wave is severely distorted by atmospheric turbulence. Thus, co-phasing detection of segmented mirrors not only includes intrinsic error between mirrors, but also error induced by turbulence. Long-exposure or an average of multiple short-exposure frames has been adopted to suppress the influence of turbulence. However, the influence of turbulence on the differential piston between two sub-apertures is challenging to quantify owing to the complexity of the problem of light propagation through turbulence. In this paper, theoretical models of differential piston variance that incorporate the influence of exposure time, wind, outer scale, and multi-layered turbulence have been proposed. Specifically, a model that only considers the differential piston caused by turbulence and a model that considers the differential piston induced by turbulence when the global tilt is removed have been derived. Removing the global tilt has been proven to be effective in mitigating the influence of turbulence and reducing the exposure time of piston detection methods. The influence of turbulence on the differential piston has been quantified and illustrated by using a simplified turbulence profile and wind vertical distribution data from the Fuxian Lake Solar Observatory as an example. The minimum exposure time for piston detection can hence be determined. A numerical experiment has been conducted to cross-validate our theory and PSF-based piston detection method. Our models can serve as a theoretical guidance on strategies to reduce the influence of turbulence on the piston detection of segmented mirrors.