25 February 2019 in Proceedings of the National Academy of Sciences
Limbless animals like snakes inhabit most terrestrial environments, generating thrust to overcome drag on the elongate body via contacts with heterogeneities. The complex body postures of some snakes and the unknown physics of most terrestrial materials frustrates understanding of strategies for effective locomotion. As a result, little is known about how limbless animals contend with unplanned obstacle contacts. We studied a desert snake, Chionactis occipitalis , which uses a stereotyped head-to-tail traveling wave to move quickly on homogeneous sand. In laboratory experiments, we challenged snakes to move across a uniform substrate and through a regular array of force-sensitive posts. The snakes were reoriented by the array in a manner reminiscent of the matter-wave diffraction of subatomic particles. Force patterns indicated the animals did not change their self-deformation pattern to avoid or grab the posts. A model using open-loop control incorporating previously described snake muscle activation patterns and body-buckling dynamics reproduced the observed patterns, suggesting a similar control strategy may be used by the animals. Our results reveal how passive dynamics can benefit limbless locomotors by allowing robust transit in heterogeneous environments with minimal sensing.
26 October 2020 in Integrative and Comparative Biology
Terrestrial organisms that use traveling waves to locomote must leverage heterogeneities to overcome drag on the elongate body. While previous studies illuminated how habitat generalist snakes self-deform to use rigid obstacles in the surroundings, control strategies for multi-component terrain are largely unknown. We compared the sand-specialist Chionactis occipitalis to a habitat generalist, Pantherophis guttatus, navigating a model terrestrial terrain–rigid post arrays on a low-friction substrate. We found the waveshapes used by the generalist were more variable than the specialist. Principal component analysis revealed that while the specialized sand-swimming waveform was always present on C. occipitalis, the generalist did not have a similarly pervasive low-dimensional waveshape. We expected the generalist to thus outperform the specialist in the arrays, but body slip of both species was comparable on level ground and in all trials the snakes successfully traversed the arena. When we further challenged the snakes to ascend an inclined lattice, the sand-specialist had difficulty maintaining contact with the obstacles and was unable to progress up the steepest inclines in the largest lattice spacings. Our results suggest that species adapted to different habitats use different control modalities—the specialist is primarily controlling its kinematics to achieve a target shape while, consistent with previous research, the generalist is using force control and self-deforms in response to terrain contacts. While both strategies allowed progress on the uninclined low-friction terrain with posts, the more variable waveshapes of the generalist may be necessary when faced with more challenging locomotor tasks like climbing inclines.
3 February 2022 in Bioinspiration & Biomimetics
The transition from the lab to natural environments is an archetypal challenge in robotics. While larger robots can manage complex limb–ground interactions using sensing and control, such strategies are difficult to implement on small platforms where space and power are limited. The Harvard Ambulatory Microrobot (HAMR) is an insect-scale quadruped capable of effective open-loop running on featureless, hard substrates. Inspired by the predominantly feedforward strategy of rapidly-running cockroaches on uneven terrain (Sponberg, 2007), we used HAMR to explore open-loop running on two 3D printed heterogeneous terrains generated using fractional Brownian motion. The ‘pocked’ terrain had foot-scale features throughout while the ‘jagged’ terrain features increased in height in the direction of travel. We measured the performance of trot and pronk gaits while varying limb amplitude and stride frequency. The frequencies tested encompassed different dynamics regimes: body resonance (10–25 Hz) and kinematic running (30–40 Hz), with dynamics typical of biological running and walking, respectively, and limb-transmission resonance (45–60 Hz). On the featureless and pocked terrains, low mechanical cost-of-transport (mCoT) kinematic running combinations performed best without systematic differences between trot and pronk; indicating that if terrain features are not too tall, a robot can transition from homo-to heterogeneous environments in open-loop. Pronk bypassed taller features than trot on the jagged terrain, and higher mCoT, lower frequency running was more often effective. While increasing input power to the robot improved performance in general, lower frequency pronking on jagged terrain allowed the robot to bypass taller features compared with the same input power at higher frequencies. This was correlated with the increased variation in center-of-mass orientation occurring at frequencies near body resonance. This study established that appropriate choice of robot dynamics, as mediated by gait, frequency, and limb amplitude, can expand the terrains accessible to microrobots without the addition of sensing or closed-loop control.
11 November 2024 in IEEE Robotics and Automation Letters
While previous studies have explored electroadhesive climbing using the insect-scale Harvard Ambulatory Microrobot platform, the robot's ability to climb reliably over irregular terrain has remained limited. To evaluate potential solutions, we conducted an investigation of the electroadhesive pad design space and characterized the shear force climbing capabilities of the robot with different pad designs. We find that on smooth, flat terrains, a large simple circular footpad structure exhibited the greatest shear forces. However, on rougher inclined surfaces, pads which adjusted the width, length, and number of spoke- like features provide greater compliance and achieve more consistent shear adhesion forces. Such compliant spoke pad designs on rough surfaces performed with 84 % stick reliability and 1.02 kPa average adhesion forces compared to 45 % stick reliability and 0.81 kPa average adhesion forces for a comparable circular pad. We demonstrate the improved climbing capability of the 4.5 cm robot on terrain with 75 $\mu$ m roughness and observe an average increase in climbing speed of 48 % over a range of angles from 0-45 degrees.
21 August 2024 in Integrative and Comparative Biology
To navigate complex terrains, insects use diverse tarsal structures (adhesive pads, claws, spines) to reliably attach to and locomote across substrates. This includes surfaces of variable roughness and inclination, which often require reliable transitions from ambulatory to scansorial locomotion. Using bioinspired physical models as a means for comparative research, our study specifically focused on the diversity of tarsal spines, which facilitate locomotion via frictional engagement and shear force generation. For spine designs, we took inspiration from ground beetles (Family Carabidae), which is a largely terrestrial group known for their quick locomotion. Evaluating four different species, we found that the hind legs host linear rows of rigid spines along the entire tarsus. By taking morphometric measurements of the spines, we highlighted parameters of interest (e.g., spine angle and aspect ratio) in order to test their relationship to shear forces sustained during terrain interactions. We systematically evaluated these parameters using spines cut from stainless steel shim attached to a small acrylic sled loaded with various weights. The sled was placed on 3D-printed models of rough terrain, randomly generated using fractal Brownian motion, while a motorized pulley system applied force to the spines. A force sensor measured the reaction force on the terrain, recording shear force before failure occurred. Initial shear tests highlighted the importance of spine angle, with bioinspired anisotropic designs producing higher shear forces. Using this data, we placed the best (50○ angle) and worst (90○ angle) performing spines on the legs of our insect-scale ambulatory robot physical model. We then tested the robot on various surfaces at 0, 10 and 20○ inclines, seeing similar success with the more bioinspired spines.