Yiorgos Tsiatouhas

Yiorgos Tsiatouhas

Auto-generated profile, based on publicly available information

Yiorgos Tsiatouhas

Department of Computer Science, University of Ioannina, Ioannina, Greece

Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 January 2010 in IEEE Transactions on Circuits and Systems I: Regular Papers
Verified
Journal Article
Closed access
LDLambros E Dermentzoglou
Lambros E Dermentzoglou
AAAngela Arapoyanni
Angela Arapoyanni
YTYiorgos Tsiatouhas
Yiorgos Tsiatouhas
This paper presents an efficient, low-cost, built-in test (BIT) circuit for radio frequency differential low noise amplifiers (DLNAs). The BIT circuit detects amplitude alterations at the outputs of the DLNA, due to parametric or catastrophic faults, and provides a single digital Pass/Fail indication signal. A triple modular redundancy approach has been adopted for the BIT circuit design to avoid possible yield loss in case of a malfunctioning test circuitry. The technique has been evaluated on a typical CMOS RF DLNA and simulation results are presented.

6 April 2015 in IEEE Transactions on Computers
Verified
Journal Article
Closed access
SVStefanos Valadimas
Stefanos Valadimas
YTYiorgos Tsiatouhas
Yiorgos Tsiatouhas
AAAngela Arapoyanni
Angela Arapoyanni
Timing errors are an increasing reliability concern in nanometer technology, high complexity and multi-voltage/frequency integrated circuits. A local error detection and correction technique is presented in this work that is based on a new bit flipping flip-flop. Whenever a timing error is detected, it is corrected by complementing the output of the corresponding flip-flop. The proposed solution is characterized by very low silicon area and power requirements compared to previous design schemes in the open literature. To validate its efficiency, it has been applied in the design of a MIPS microprocessor core in a 90 nm technology, while a demonstration version of the same core in an FPGA platform is presented.

12 February 2019 in IEEE Transactions on Device and Materials Reliability
Verified
Journal Article
Closed access
HDHelen-Maria Dounavi
Helen-Maria Dounavi
YSYiorgos Sfikas
Yiorgos Sfikas
YTYiorgos Tsiatouhas
Yiorgos Tsiatouhas

20 August 2013 in IEEE Transactions on Computer-Aided Design of Integrated Circuits and Systems
Verified
Journal Article
Closed access
John LiaperdosJohn Liaperdos
John Liaperdos
AAAngela Arapoyanni
Angela Arapoyanni
YTYiorgos Tsiatouhas
Yiorgos Tsiatouhas
A method for the optimization of the efficiency of alternate tests for adjustable RF mixers is presented in this paper. Alternate tests provide a cost- and time-effective substitute for their conventional specification-based counterparts by attempting to predict rather than directly measuring a circuit's performance from its response to suitable test stimuli. In order to provide post-manufacture yield recovery through calibration, integrated RF circuits-especially nanometric circuits-are often designed to present some form of adjustability. Such a property offers a set of discrete states of operation, from which a performance-compliant state is selected by calibration. In general, an alternate test can be conducted for each discrete state of operation, thus providing a large set of test observables from which regression models can be constructed to predict performance in all available states. However, test time and cost concerns impose that the derivation of the predictive models should be performed through an optimization procedure that aims to select a subset of the test observables that minimizes a certain cost criterion. In this paper, alternate tests for adjustable RF mixers are considered where the test response consists of dc voltage levels that appear at certain circuit nodes while the mixer operates in homodyne mode. Selection algorithms are applied to determine the optimum observables from the test response. Simulations on a typical RF mixer, designed in an 0.18- μm CMOS technology, have shown significant improvement in the corresponding alternate test efficiency.

11 December 2006 in IEEE Transactions on Circuits and Systems I: Regular Papers
Verified
Journal Article
Closed access
KLKonstantinos Limniotis
Konstantinos Limniotis
YTYiorgos Tsiatouhas
Yiorgos Tsiatouhas
THThemistoklis Haniotakis
Themistoklis Haniotakis
AAAngela Arapoyanni
Angela Arapoyanni
In this work, a design technique to reduce the energy consumption in NO RAce (NORA) circuits is presented. The technique is based on a unidirectional switch topology combined with a new clocking scheme permitting both charge recycling between circuit nodes and elimination of the short circuit current. Calculations proved that energy savings higher than 20% can be achieved. Simulation results from NORA designs in a 0.18-mum CMOS technology are presented to demonstrate the effectiveness of the proposed technique to achieve both energy and energy-delay product reduction

1 May 2015
Verified
Conference Paper
Closed access
AAAnthi Anastasiou
Anthi Anastasiou
YTYiorgos Tsiatouhas
Yiorgos Tsiatouhas
AAAngela Arapoyanni
Angela Arapoyanni
Timing errors are a major threat in nanometer technology integrated circuits. Razor is a well known timing error tolerance design technique. However, its silicon area cost makes it unattractive for widespread use. In this work, we reuse the Razor topology in order to achieve low power scan testing operations and make this technique a viable solution which will serve both on-line and off-line testing requirements. In addition, the ability to apply this technique for at-speed scan testing is also explored in this work. According to the experimental results, the scan power consumption is drastically reduced since the signal transitions at the inputs of the combinational logic are eliminated during the scan testing operations.