Mojtaba Movahedi

Mojtaba Movahedi

Auto-generated profile, based on publicly available information

Mojtaba Movahedi

Faculty of Materials Science and Engineering, Sharif University of Technology, Tehran, Iran

Research Focus & Metrics

Academic Career Length

20Years (2007-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 July 2016 in Materials & Design
Verified
Journal Article
Closed access
MAM.R. Arghavani
M.R. Arghavani
MMM. Movahedi
M. Movahedi
AKA.H. Kokabi
A.H. Kokabi

1 February 2013 in Materials & Design (1980-2015)
Verified
Journal Article
Closed access
MMM. Movahedi
M. Movahedi
AKA.H. Kokabi
A.H. Kokabi
SRS.M. Seyed Reihani
S.M. Seyed Reihani
WCW.J. Cheng
W.J. Cheng
CWC.J. Wang
C.J. Wang

1 February 2012 in Science and Technology of Welding and Joining
Verified
Journal Article
Closed access
MMM Movahedi
M Movahedi
AKA H Kokabi
A H Kokabi
SRS M Seyed Reihani
S M Seyed Reihani
HNH Najafi
H Najafi
In this study, Al-5083 and St-12 alloy sheets were friction stir lap welded at different travel (7–23 cm min−1) and rotation (750–1125 rev min−1) speeds of the welding tool. The welded joints were characterised by various methods including shear tensile and Vickers microhardness tests, optical and scanning electron microscopies and X-ray diffraction analysis. The results showed that the weld zone defects decreased, and the joint strength also improved significantly with the reducing tool travel speed from 23 to 7 cm min−1. The travel speed of 11 cm min−1 was an optimum speed within the travel speeds investigated in this work. Additionally, raising the tool rotation speed enhanced the joint strength slightly. The microhardness results confirmed the formation of intermetallic phase layer with the hardness of ∼335 HV at the swirl layered structure.

1 October 2015 in Journal of Materials Processing Technology
Verified
Journal Article
Closed access
EFEskandar Fereiduni
Eskandar Fereiduni
MMM. Movahedi
M. Movahedi
AKA.H. Kokabi
A.H. Kokabi

1 February 2017 in Science and Technology of Welding and Joining
Verified
Journal Article
Closed access
HSH. Shahmiri
H. Shahmiri
MMM. Movahedi
M. Movahedi
AKA. H. Kokabi
A. H. Kokabi
Joining feasibility of aluminium alloy to polypropylene sheets via friction stir lap joining was examined. Effects of heat-input on microstructure and mechanical behaviour of the joints were investigated. A covering plate was used to confine flow of molten polymer. The results showed a distinctive interaction layer at polymer/aluminium interface, consisted mainly of C, O and Al. Shear strength of the joints decreased by enhancement of the heat-input due to increase in the thickness of the interaction layer as well as the gap width between this layer and both aluminium and polymer matrices. Maximum shear-tensile strength of 5.1 MPa (∼20% of polymer shear strength) was obtained, which was higher than or comparable to that of the joints produced by other processes.

1 May 2017 in Science and Technology of Welding and Joining
Verified
Journal Article
Closed access
MTM. Tamizi
M. Tamizi
Majid PouranvariMajid Pouranvari
Majid Pouranvari
MMM. Movahedi
M. Movahedi
The paper addresses the process–microstructure–performance relationships in resistance spot welding of a martensitic advanced high strength steel. Significant softening was observed in the heat affected zone (HAZ) due to allotriomorphic ferrite formation in the inter-critical HAZ and tempering of martensite in sub-critical HAZ (SCHAZ), with the latter plays more important role in mechanical properties of the spot welds. The strain concentration associated with the HAZ softening promotes initiation of pullout failure from the soft SCHAZ. While, the peak load in the interfacial failure mode is governed by the fusion zone size, that of the pullout mode is significantly affected by the HAZ softening. To improve weldability of martensitic steels, the HAZ softening should be minimised via modifications in welding process or steel chemistry.