Mykhaylo Bloshchytsyn

Mykhaylo Bloshchytsyn

Auto-generated profile, based on publicly available information

Mykhaylo Bloshchytsyn

Igor Sikorsky Kyiv Polytechnic Institute

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
29 December 2022 in Mechanics and Advanced Technologies
Verified
Journal Article
Open access
LGLeonid Golovko
Leonid Golovko
OKOLeksii Kaglyak
OLeksii Kaglyak
VRViktor Romanenko
Viktor Romanenko
MBMykhaylo Bloshchytsyn
Mykhaylo Bloshchytsyn
The problem of the article is designed to reveal the proposed, developed and researched new method of improving the adhesion strength of plasma wear-resistant coatings on the outer surfaces of weapons made of high-alloy, heat-resistant steels, using additional cyclic (3-4) times their heating by laser radiation to temperatures of 0.6 – 0.8Tpl for a few milliseconds. The purpose of increasing the resource of use and the quality of the appearance of the weapon by applying wear-resistant coatings with increased adhesion strength to the base using plasma gas-thermal spraying followed by laser thermal cycling. Determination of the main factors and parameters of the process of laser thermocycling of plasma coatings, their interrelationships, development of an algorithm for determining the conditions of laser thermocycling, establishment of the rational range of their values by mathematical modeling and experimental research. The results of mathematical modeling of laser cyclic heating of plasma coatings of HTN of different thicknesses are presented, which allows determining the irradiation parameters that ensure their heating to temperatures at the "coating-substrate" boundary ≤1000ºС, on the surface - to Т< Тpl, at maximum cooling rates. It has been proven that laser thermocycling provides an increase in the adhesion strength of coatings to the base from 14–18 to 90–110 MPa, a decrease in porosity from 10–12% to 7–8%, which is due to the redistribution of alloying components at the “coating–base” interface, with the formation of elements of the metallurgical connection, contributes to a significant increase in wear resistance and a decrease in the coefficient of friction due to the formation of secondary ultradispersed film structures. We consider laser thermocycling of plasma coatings is an effective method of improving their quality and strength of adhesion to the base.

1 January 2022 in TECHNICAL SCIENCES AND TECHNOLOGIES
Verified
Journal Article
Open access
PDF file
NINational Technical University of Ukraine «Igor Sikorsky Kyiv Polytechnic Institute»
National Technical University of Ukraine «Igor Sikorsky Kyiv Polytechnic Institute»
VRVictor Romanenko
Victor Romanenko
LGLeonid Golovko
Leonid Golovko
MBMykhailo Bloshchytsyn
Mykhailo Bloshchytsyn
VDViktor Dubniuk
Viktor Dubniuk
ВДВіктор Дубнюк
Віктор Дубнюк
The analysis of existing methods and a new combined process of bimetal production are presented, according to which a special regular design of holders is created on the surface of its functional component by means of laser or arc welding. Themelt of the structural component of the bimetal is fed to the surface of the functional component through the hole in the form of a special device with a given flow rate. Holders are made of wire. The holders are located on the surface of the working plate at an angle or perpendicular to the base, followed by bending after assembly. The number of holders, their geometry and relative position on the surface are determined by the size of the bimetal. You can change the required parameters of the strength of adhesion in different areas. Full filling of technological space between holders filled with metal guarantees reliable fastening ofbimetallic plates. Various options have been developed and implemented to reduce the cost of bimetal production technology. There are options where not the whole surface is filled, but only the specified areas of the prepared holes. This allows to implement multi-layer metal structures. A cheap and simple method of obtaining bimetallic plates without the need for foundry operations and equipment is the use of welding technology. It has been proven that in order to ensure high bond strength of bimetallic components and uniform distribution on the joint plane, it is necessary that the frequency of the holders and the step between them havethe optimal value. The high efficiency of a new, innovative combined technology of bimetal production has been demonstrated.The introduction of these technologies in the production of bimetals does not require large material costs and ensures maximum profitability of the manufacturing process of such materials. The presence of several manufacturing methods allows you to select the most optimal technology depending on the volume of production and the size of the resulting sheets of bimetals or individual products from them.

10 June 2024 in Mechanics and Advanced Technologies
Verified
Journal Article
Open access
PDF file
VRViktor Romanenko
Viktor Romanenko
MBMykhaylo Bloshchytsyn
Mykhaylo Bloshchytsyn
MRMaksym Romanenko
Maksym Romanenko
AKAndriy Kushnerenko
Andriy Kushnerenko
This article considered the problem of improving the quality of the edges of parts cut by laser radiation, due to a new approach, which consists in smoothing the surface of laser cuts with a ball tool. The conducted analysis showed the prospects of improving the characteristics of the technology of laser cutting parts from sheets of different thickness when applying subsequent ball smoothing of the cut surface. The purpose of the study is a comprehensive analysis of the effect of smoothing parameters on the operational characteristics of parts obtained by this combined method. The necessary methods of assessing the roughness of the cut surfaces, the microhardness of their edges, and the residual stresses occurring in the surface layer of the cut were used to conduct the experiments. Based on the formulated hypothesis about the prospect of improving the characteristics of the cut edges during their subsequent smoothing, it was experimentally established that there is a noticeable decrease in the values of roughness parameters after smoothing the surface of laser cuts compared to their values for samples only after laser cutting. In addition, studies show that in the region of the edge of the cut, there is an increase in the microhardness of the cut surface by up to 20%. At the same time, compressive stresses appear on the edge of the cut, which ensure an increase in the operational characteristics of the parts after the proposed combined treatment. To implement the researched technology of smoothing the laser cut surface, the design of the smoothing head was proposed. As a result of the study of the proposed combined method of obtaining parts by laser cutting with subsequent smoothing of the surface of the cuts, it was confirmed that with low additional capital costs, it is possible to significantly improve the operational characteristics of the parts produced in this way. This also proves the prospects for further development of the presented combined technology, both with the use of ball smoothing and with the application of other methods of surface strengthening of laser cut edges.

1 January 2022 in TECHNICAL SCIENCES AND TECHNOLOGIES
Verified
Journal Article
Open access
PDF file
NINational Technical University of Ukraine «Igor Sikorsky Kyiv Polytechnic Institute»
National Technical University of Ukraine «Igor Sikorsky Kyiv Polytechnic Institute»
VRVictor Romanenko
Victor Romanenko
MBMykhaylo Bloshchytsyn
Mykhaylo Bloshchytsyn
IZIvan Zheget
Ivan Zheget
YYYuriy Yurchenko
Yuriy Yurchenko
ЮЮЮрій Юрченко
Юрій Юрченко
An analysis of the existing methods of laser cutting is given and the features of constructive and technological improvement of the process are presented. The technology of laser cutting of metals, in particular sheet metal, is constantlybeing improved and modernized. Expanding the functionality of existing equipment on the market can be done by using two or more laser heads. The laser heads move synchronously and are programmatically coordinated among themselves in six coordinates. This allows not only to increase the speed of the cutting process, but also provides the possibility of simultaneously cutting several different parts or holes from one sheet or more sheets, which ensures the expansion of functionality, as wellas the acceleration of the cutting process.At the same time, the disadvantages of the traditional method of contour laser cutting are the low quality of the cut edges. To improve the quality of laser cutting, it is recommended to reduce the thermal effect on the metal of the workpiece with the help of a cooling liquid sprayed along with the gas flow, which allows to reduce the thermal conductivity of the metal of the workpiece. A significant drawback of this method is the complex design of the laser installation. Taking into account other disadvantages of the traditional contour laser cutting method (non-perpendicularity and high roughness) and the possible range of metal thicknesses, a combined laser cutting method was proposed. A combined laser installation was developed, where sheet metal is subjected to mechanical activation before laser cutting, which consists in cold plastic deformation. At the same time, the mechanical activation of the metal sheet occurs, which leads to a decrease in the thermal conductivity of the metaldue to its deformation hardening and, as a result, a reduction (localization) of the zone of thermal influence in the cutting zone. The observed effect is due to the compaction of the crystal lattice of the metal, the increase in the density of dislocationsduring plastic deformation. Whenapplying preliminary deformation, not only the width of the cut in the metal is reduced, but also the roughness of the cut surface and the size of the thermally affected zone at its edges.The presented technological solution makes it possible to reduce the cost of the product by reducing the labor intensity of further metalwork as a result of increasing the accuracy of dimensions and reducing the roughness of the cut surface and significantly reducing the width of the cut.