Liyu Huang

Liyu Huang

Auto-generated profile, based on publicly available information

Liyu Huang

Institute of Bioengineering, The University of Edinburgh, Edinburgh, U.K

Research Focus & Metrics

Academic Career Length

12Years (2015-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
30 January 2015 in IEEE Microwave and Wireless Components Letters
Verified
Journal Article
Closed access
SJSheng-Lyang Jang
Sheng-Lyang Jang
LHLi-Yu Huang
Li-Yu Huang
CHChing-Wen Hsue
Ching-Wen Hsue
JHJhin Fang Huang
Jhin Fang Huang
A wide locking range CMOS LC-tank injection locked frequency divider (ILFD) is proposed and it uses a pre-amplifier stage in series with a post-injection mixer. The injection signal is fed to a pre-amplifier to enhance the injection signal at the post-mixer gate in the divide-by-2 ILFD. The gate of mixer is biased in sub-threshold to provide large output voltage. At the supply voltage of 0.85 V, tunable free-running low-frequency band from 3.23 to 3.59 GHz and high-band from 1.71 to 1.73 GHz are found. The low-/high-band locking range is (61.7%) from 2.8 to 5.3 GHz/(64.9%) from 5.1~10.0 GHz.

9 November 2020 in IEEE Access
Verified
Journal Article
Open access
LHLiyu Huang
Liyu Huang
AMAlan Murray
Alan Murray
BFBrian W. Flynn
Brian W. Flynn
In this article, the so-called bootstrapping rectifier (BSR) proposed by Hashemi et al. is re-analyzed, and a novel high-efficiency low-power rectifier called Opto-Coupled Dynamic Gate-Control (OCDGC) rectifier is presented based on the bootstrapping structure. Circuit analysis of BSR shows that the rectifier design has inherent problems that cause a high forward voltage drop and limit its power conversion efficiency (PCE). The BSR is simulated and fabricated in TSMC $0.18~\mu \text{m}$ process, and both simulation and experiment results prove the analysis. Inspired by the idea of bootstrapping structure, the presented OCDGC rectifier utilizes an opto-coupler to control the on-off switching of the active diode to maximize input power and prevent reverse leakage. A feedback loop is also introduced in the rectifier to limit the forward voltage drop. The proposed design is simulated in the TSMC $0.18~\mu \text{m}$ process. Simulation results show that, with a 3 MHz input, OCDGC rectifier is able to achieve more than 80% PCE at an input power down to 0.55 mW and achieve a forward voltage drop less than 0.1 V. More than 20% PCE improvement is achieved compared with the PCE of BSR.

19 October 2020 in IEEE Access
Verified
Journal Article
Open access
LHLiyu Huang
Liyu Huang
AMAlan Murray
Alan Murray
BFBrian W. Flynn
Brian W. Flynn
This paper presents a design methodology for a 3-coil magnetic resonance wireless power transfer (WPT) system with a long transfer distance (up to 20 cm) and a small implanted receiver (RX) (2mm in diameter) at a specific frequency. The methodology aims to find out the optimal value of dimensional parameters (i.e., coil diameter, gap interval and coil turn number) of the transmitter (TX) coils to maximize the magnetic field strength at the target distance while keeping the coil self-resonant frequency (SRF) twice of the target operational frequency. Firstly, the circuit model of the TX circuits is developed, which include a single-turn coupling coil and a multi-turn primary coil. Secondly, the co-dependences between the dimensional parameters are analyzed, which shows the dominant factors and secondary factors of each dimensional parameter, and how the optimal values of dimensional parameters are changed by these factors. Based on the analysis, design flow of the TX circuit is proposed to decide the optimal values of dimensional parameters given the transfer distance, source voltage, operational frequency and wire diameter. Using the design flow, optimal values of dimensional parameters are predicted for 20-cm transfer distance and 16-cm transfer distance and are verified with finite element analysis (FEA) software COMSOL Multiphysics. With the optimal TX design, the power received by a 2-mm ferrite core solenoid RX is calculated. At 20 cm transfer distance, up to 4.3 mW can be achieved in air, and 0.8 mW can be achieved in conductive human tissue.