Objective: To evaluate the pharmacokinetics, safety, and tolerability of brivaracetam (BRV) as 15‐min intravenous (IV) infusion and bolus (≤2‐min injection).Methods: EP0065 (ClinicalTrials.gov: NCT03405714) was a Phase 2, multicenter, open‐label trial in patients ≥1 month to <16 years of age with epilepsy. Patients received up to 5 mg/kg/day BRV (not exceeding 200 mg/day). Enrollment was sequential by descending age, depending on safety review. Outcomes included BRV plasma concentrations before and after IV administration, treatment‐emergent adverse events (TEAEs), and discontinuations due to TEAEs.Results: Fifty patients were enrolled, received BRV, and completed the trial. Twenty‐six patients (52.0%) received 15‐min infusions and 24 (48.0%) received bolus injections. Most patients (80.0%) received one IV dose. In the 15‐min infusion group, geometric mean (GeoMean) BRV concentrations 15 (±2) min (n = 21) and 3 h (±15 min) (n = 21) post dose were 1903.0 ng/mL (geometric coefficient of variation [GeoCV]: 60.7%) and 1130.3 ng/mL (58.8%), respectively. In the bolus group, GeoMean BRV concentrations 15 (±2) min (n = 19) and 3 h (±15 min) (n = 21) post dose were 1704.8 ng/mL (GeoCV: 74.5%) and 1383.9 ng/mL (85.0%), respectively. Overall, 14 patients (28.0%) had TEAEs (15‐min infusion: 8 [30.8%]; bolus: 6 [25.0%]), most commonly (≥5% of patients) somnolence (3 [6.0%]). Ten patients (20.0%) had drug‐related TEAEs (15‐min infusion: 6 [23.1%]; bolus: 4 [16.7%]). No patients discontinued due to TEAEs, and no deaths occurred.Significance: IV BRV (up to 200 mg/day) was well tolerated in patients ≥1 month to <16 years of age, regardless of whether BRV was administered as 15‐min infusion or bolus. No unexpected safety or pharmacokinetic differences were observed between patients receiving 15‐min infusions or bolus, and plasma concentrations were in the expected range. Safety results were consistent with the known safety profile of oral BRV, with no new safety concerns identified.
Background: The continual reassessment method (CRM) identifies the maximum tolerated dose (MTD) more efficiently and identifies the true MTD more frequently compared to standard methods such as the 3 + 3 method. An initial estimate of the dose-toxicity relationship (prior skeleton) is required, and there is limited guidance on how to select this. Previously, we compared the CRM with six different skeletons to the 3 + 3 method by conducting post-hoc analysis on a phase 1 oncology study (AZD3514), each CRM model reduced the number of patients allocated to suboptimal and toxic doses. This manuscript extends this work by assessing the ability of the 3 + 3 method and the CRM with different skeletons in determining the true MTD of various “true” dose-toxicity relationships. Methods: One thousand studies were simulated for each “true” dose toxicity relationship considered, four were based on clinical trial data (AZD3514, AZD1208, AZD1480, AZD4877), and four were theoretical. The 3 + 3 method and 2-stage extended CRM with six skeletons were applied to identify the MTD, where the true MTD was considered as the largest dose where the probability of experiencing a dose limiting toxicity (DLT) is ≤33%. Results: For every true dose-toxicity relationship, the CRM selected the MTD that matched the true MTD in a higher proportion of studies compared to the 3 + 3 method. The CRM overestimated the MTD in a higher proportion of simulations compared to the 3 + 3 method. The proportion of studies where the correct MTD was selected varied considerably between skeletons. For some true dose-toxicity relationships, some skeletons identified the true MTD in a higher proportion of scenarios compared to the skeleton that matched the true dose-toxicity relationship. Conclusion: Through simulation, the CRM generally outperformed the 3 + 3 method for the clinical and theoretical true dose-toxicity relationships. It was observed that accurate estimates of the true skeleton do not always outperform a generic skeleton, therefore the application of wide confidence intervals may enable a generic skeleton to be used. Further work is needed to determine the optimum skeleton.