Vesa Vuorinen

Vesa Vuorinen

Auto-generated profile, based on publicly available information

Vesa Vuorinen

Department of Electrical Engineering and Automation, School of Electrical Engineering, Aalto University, Aalto, Finland

Research Focus & Metrics

Academic Career Length

29Years (1998-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2005 in Materials Science and Engineering: R: Reports
Verified
Journal Article
Closed access
TLTomi Laurila
Tomi Laurila
VVV. Vuorinen
V. Vuorinen
JKJ.K. Kivilahti
J.K. Kivilahti

1 March 2010 in Materials Science and Engineering: R: Reports
Verified
Journal Article
Closed access
TLTomi Laurila
Tomi Laurila
VVV. Vuorinen
V. Vuorinen
MPM. Paulasto-Kröckel
M. Paulasto-Kröckel

1 January 2014
Verified
Book
Closed access
APAloke Paul
Aloke Paul
TLTomi Laurila
Tomi Laurila
VVVesa Vuorinen
Vesa Vuorinen
SDSergiy V. Divinskiy
Sergiy V. Divinskiy

1 July 2002 in IEEE Transactions on Electronics Packaging Manufacturing
Verified
Journal Article
Closed access
KZKejun Zeng
Kejun Zeng
VVV. Vuorinen
V. Vuorinen
JKJ.K. Kivilahti
J.K. Kivilahti
Transmission electron microscopy and scanning electron microscopy were employed to analyze the interfacial microstructure between Sn-Ag-Cu solder alloys and Ni(P)/Au metallizations. The intermetallic compound Cu/sub 6/Sn/sub 5/, containing a small amount of dissolved Ni, was found to form preferentially on the Ni coating. This compound layer served as a barrier for direct reaction of Sn with the Ni(P) coating. On the Ni(P) side, a nickel phosphide was identified. Thermodynamic evaluation of the Cu-Ni-Sn system was carried out to rationalize the enrichment of Cu at the solder/finish interface. Effects of the interfacial reactions on joint reliability are discussed.

1 March 2009 in Microelectronics Reliability
Verified
Journal Article
Closed access
TLTomi Laurila
Tomi Laurila
JHJ. Hurtig
J. Hurtig
VVV. Vuorinen
V. Vuorinen
JKJ.K. Kivilahti
J.K. Kivilahti

14 March 2008 in Journal of Electronic Materials
Verified
Journal Article
Open access
PDF file
VVV. Vuorinen
V. Vuorinen
HYH. Yu
H. Yu
TLTomi Laurila
Tomi Laurila
JKJ.K. Kivilahti
J.K. Kivilahti
Interfacial reactions between liquid Sn and various Cu-Ni alloy metallizations as well as the subsequent phase transformations during the cooling were investigated with an emphasis on the microstructures of the reaction zones. It was found that the extent of the microstructurally complex reaction layer (during reflow at 240°C) does not depend linearly on the Ni content of the alloy metallization. On the contrary, when Cu is alloyed with Ni, the rate of thickness change of the total reaction layer first increases and reaches a maximum at a composition of about 10 at.% Ni. The reaction layer is composed of a relatively uniform continuous (Cu,Ni)6Sn5 reaction layer (a uniphase layer) next to the NiCu metallizations and is followed by the two-phase solidification structures between the single-phase layer and Sn matrix. The thickness of the two-phase layer, where the intermetallic tubes and fibers have grown from the continuous interfacial (Cu,Ni)6Sn5 layer, varies with the Ni-to-Cu ratio of the alloy metallization. In order to explain the formation mechanism of the reaction layers and their observed kinetics, the phase equilibria in the Sn-rich side of the SnCuNi system at 240°C were evaluated thermodynamically utilizing the available data, and the results of the Sn/Cu x Ni1−x diffusion couple experiments. With the help of the assessed data, one can also evaluate the minimum Cu content of Sn-(Ag)-Cu solder, at which (Ni,Cu)3Sn4 transforms into (Cu,Ni)6Sn5, as a function of temperature and the composition of the liquid solders.