Quantitative interpretation of the tidal response of water levels measured in wells has long been made either with a model for perfectly confined aquifers or with a model for purely unconfined aquifers. However, many aquifers may be neither totally confined nor purely unconfined at the frequencies of tidal loading but behave somewhere between the two end‐members. Here we present a more general model for the tidal response of groundwater in aquifers with both horizontal flow and vertical leakage. The model has three independent parameters: the transmissivity (T) and storativity (S) of the aquifer and the specific leakage (K′/b′) of the leaking aquitard, where K′ and b′ are the hydraulic conductivity and the thickness of the aquitard, respectively. If T and S are known independently, this model may be used to estimate aquitard leakage from the phase shift and amplitude ratio of water level in wells obtained from tidal analysis. We apply the model to interpret the tidal response of water level in a US Geological Survey (USGS) deep monitoring well installed in the Arbuckle aquifer in Oklahoma, into which massive amount of wastewater coproduced from hydrocarbon exploration has been injected. The analysis shows that the Arbuckle aquifer is leaking significantly at this site. We suggest that the present method may be effective and economical for monitoring leakage in groundwater systems, which bears on the safety of water resources, the security of underground waste repositories, and the outflow of wastewater during deep injection and hydrocarbon extraction.
7 December 2017 in Geochemistry, Geophysics, Geosystems
Fault rock assemblages reflect interaction between deformation, stress, temperature, fluid, and chemical regimes on distinct spatial and temporal scales at various positions in the crust. Here we interpret measurements made in the hanging‐wall of the Alpine Fault during the second stage of the Deep Fault Drilling Project (DFDP‐2). We present observational evidence for extensive fracturing and high hanging‐wall hydraulic conductivity (∼10−9to 10−7m/s, corresponding to permeability of ∼10−16to 10−14m2) extending several hundred meters from the fault's principal slip zone. Mud losses, gas chemistry anomalies, and petrophysical data indicate that a subset of fractures intersected by the borehole are capable of transmitting fluid volumes of several cubic meters on time scales of hours. DFDP‐2 observations and other data suggest that this hydrogeologically active portion of the fault zone in the hanging‐wall is several kilometers wide in the uppermost crust. This finding is consistent with numerical models of earthquake rupture and off‐fault damage. We conclude that the mechanically and hydrogeologically active part of the Alpine Fault is a more dynamic and extensive feature than commonly described in models based on exhumed faults. We propose that the hydrogeologically active damage zone of the Alpine Fault and other large active faults in areas of high topographic relief can be subdivided into an inner zone in which damage is controlled principally by earthquake rupture processes and an outer zone in which damage reflects coseismic shaking, strain accumulation and release on interseismic timescales, and inherited fracturing related to exhumation.
Young rifts are shaped by combined tectonic and surface processes and climate, yet few records exist to evaluate the interplay of these processes over an extended period of early rift-basin development. Here, we present the longest and highest resolution record of sediment flux and paleoenvironmental changes when a young rift connects to the global oceans. New results from International Ocean Discovery Program (IODP) Expedition 381 in the Corinth Rift show 10s–100s of kyr cyclic variations in basin paleoenvironment as eustatic sea level fluctuated with respect to sills bounding this semi-isolated basin, and reveal substantial corresponding changes in the volume and character of sediment delivered into the rift. During interglacials, when the basin was marine, sedimentation rates were lower (excepting the Holocene), and bioturbation and organic carbon concentration higher. During glacials, the basin was isolated from the ocean, and sedimentation rates were higher (~2–7 times those in interglacials). We infer that reduced vegetation cover during glacials drove higher sediment flux from the rift flanks. These orbital-timescale changes in rate and type of basin infill will likely influence early rift sedimentary and faulting processes, potentially including syn-rift stratigraphy, sediment burial rates, and organic carbon flux and preservation on deep continental margins worldwide.
17 October 2017 in New Zealand Journal of Geology and Geophysics
During the second phase of the Alpine Fault, Deep Fault Drilling Project (DFDP) in the Whataroa River, South Westland, New Zealand, bedrock was encountered in the DFDP‐2B borehole from 238.5–893.2 m Measured Depth (MD). Continuous sampling and meso‐ to microscale characterisation of whole rock cuttings established that, in sequence, the borehole sampled amphibolite facies, Torlesse Composite Terrane‐derived schists, protomylonites and mylonites, terminating 200–400 m above an Alpine Fault Principal Slip Zone (PSZ) with a maximum dip of 62°. The most diagnostic structural features of increasing PSZ proximity were the occurrence of shear bands and reduction in mean quartz grain sizes. A change in composition to greater mica:quartz + feldspar, most markedly below c. 700 m MD, is inferred to result from either heterogeneous sampling or a change in lithology related to alteration. Major oxide variations suggest the fault‐proximal Alpine Fault alteration zone, as previously defined in DFDP‐1 core, was not sampled.
1 May 2013 in Geochemistry, Geophysics, Geosystems
In situ stress and pore pressure are key parameters governing rock deformation, yet direct measurements of these quantities are rare. During Integrated Ocean Drilling Program (IODP) Expedition #319, we drilled through a forearc basin at the Nankai subduction zone and into the underlying accretionary prism. We used the Modular Formation Dynamics Tester tool (MDT) for the first time in IODP to measure in situ minimum stress, pore pressure, and permeability at 11 depths between 729.9 and 1533.9 mbsf. Leak‐off testing at 708.6 mbsf conducted as part of drilling operations provided a second measurement of minimum stress. The MDT campaign included nine single‐probe (SP) tests to measure permeability and in situ pore pressure and two dual‐packer (DP) tests to measure minimum principal stress. Permeabilities defined from the SP tests range from 6.53 × 10−17 to 4.23 × 10−14 m2. Pore fluid pressures are near hydrostatic throughout the section despite rapid sedimentation. This is consistent with the measured hydraulic diffusivity of the sediments and suggests that the forearc basin should not trap overpressures within the upper plate of the subduction zone. Minimum principal stresses are consistently lower than the vertical stress. We estimate the maximum horizontal stress from wellbore failures at the leak‐off test and shallow MDT DP test depths. The results indicate a normal or strike‐slip stress regime, consistent with the observation of abundant active normal faults in the seaward‐most part of the basin, and a general decrease in fault activity in the vicinity of Site C0009.
Earthquakes have been inferred to induce hydrological changes in aquifers on the basis of either changes to well water‐levels or tidal behavior, but the relationship between these changes remains unclear. Here, changes in tidal behavior and water‐levels are quantified using a hydrological network monitoring gravel aquifers in Canterbury, New Zealand, in response to nine earthquakes (of magnitudes Mw 5.4 to 7.8) that occurred between 2008 and 2015. Of the 161 wells analyzed, only 35 contain water‐level fluctuations associated with “Earth + Ocean” (7) or “Ocean” (28) tides. Permeability reduction manifest as changes in tidal behavior and increased water‐levels in the near field of the Canterbury earthquake sequence of 2010–2011 support the hypothesis of shear‐induced consolidation. However, tidal behavior and water‐level changes rarely occurred simultaneously (~2%). Water‐level changes that occurred with no change in tidal behavior reequilibrated at a new postseismic level more quickly (on timescales of ~50 min) than when a change in tidal behavior occurred (~240 min to 10 days). Water‐level changes were more than likely to occur above a peak dynamic stress of ~50 kPa and were more than likely to not occur below ~10 kPa. The minimum peak dynamic stress required for a tidal behavior change to occur was ~0.2 to 100 kPa.