Shongtao Dai

Shongtao Dai

Auto-generated profile, based on publicly available information

Shongtao Dai

Office of Materials and Road Research, Minnesota Department of Transportation, Maplewood, MN

Research Focus & Metrics

Academic Career Length

17Years (2010-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
26 June 2019 in Geosciences
Verified
Journal Article
Open access
PDF file
KHKyle Hoegh
Kyle Hoegh
RRRoger Roberts
Roger Roberts
SDShongtao Dai
Shongtao Dai
ETEyoab Zegeye Teshale
Eyoab Zegeye Teshale
Asphalt pavement compaction quality control and quality assurance (QC/QA) are traditionally based on destructive drilled cores and/or nuclear gauge results, which both are spot measurements representing significantly less than 1 percent of the in-service pavement. Ground penetrating radar (GPR) is emerging as a tool that can be used for nondestructive continuous assessment of asphalt pavement compaction quality through measuring the pavement dielectric constant. Previous studies have established that asphalt pavement dielectric constant measurements are inversely proportional to the air void content for a given asphalt mixture. However, field cores are currently required to calibrate the measured dielectric constant to the pavement density. In this paper, a method is proposed to eliminate the need for field calibration cores by measuring the dielectric constant of asphalt specimens compacted to various air void contents. This can be accomplished with a superpave gyratory compactor (SGC), which is routinely used in the pavement industry to fabricate 6 in. (15.2 cm.) diameter specimens. However, this poses difficulties with the GPR antenna height, direct coupling, and the Fresnel zone in relation to the asphalt specimen dimension limitation. These challenges are overcome by employing a plastic spacer with a known dielectric constant between the SGC specimen and the antenna. The purpose of the spacer is to reduce GPR wave speed so that the signal reflected from the specimen is separated from the direct coupling effects at an antenna height where the Fresnel zone of the GPR is not affected by the specimen dimension. The specimen dielectric constant can then be measured using the reflection coefficient-based surface reflection method (SR) or the pulse velocity-based time-of-flight method (TOF). Also, The Hoegh–Dai model (HD model) is demonstrated to reasonably predict pavement density based on the results of field measurements and corresponding core validation, especially as compared to the conventional exponential model. Results are presented from multiple days of paving on one project, as well as a single paving day on a project with significantly different mix properties. The agreement between the HD model, coreless prediction, and field cores shows the promise for implementation of dielectric-based asphalt compaction evaluation without the need for destructive field core calibration.

1 September 2020 in Journal of Transportation Engineering, Part B: Pavements
Verified
Journal Article
Open access
PDF file
TSTrevor Steiner
Trevor Steiner
KHKyle Hoegh
Kyle Hoegh
ETEyoab Zegeye Teshale
Eyoab Zegeye Teshale
SDShongtao Dai
Shongtao Dai
Traditional measures of asphalt compaction rely primarily on random cores that only measure a small fraction of the pavement. Recently, the use of ground penetrating radar was indicated to be usable as a nondestructive means for the continuous assessment of asphalt compaction. A proposed Hoegh-Dai (HD) model has been successful in predicting air void content within typically achieved field compaction levels but has reduced accuracy at the extremes. This paper proposes an enhanced Minnesota DOT (MnDOT) model to address this issue. A method for assessing modeling quality is proposed to quantify the improvement of the MnDOT model. The procedure is based on the accuracy of fits when run through a Monte Carlo simulation. The developed procedure indicates that the MnDOT model has improved accuracy—with 0.74% air void variation at a dielectric of 4 compared with 3.83% for the HD fit. Additionally, the MnDOT model is more stable for replicate days of the same mix design and falls within the uncertainty of more of the field cores across several projects than the HD model.

7 September 2017
Verified
Conference Paper
Closed access
KHKyle Hoegh
Kyle Hoegh
SDShongtao Dai
Shongtao Dai
Air void content is a crucial parameter affecting long term pavement performance. Ground penetrating radar (GPR) offers a nondestructive method of determining relative asphalt air void content cheaply, quickly, and over an entire project. Previous implementations of GPR for the determination of air void content, including demonstrations as part of a recent SHRP2 study, were mostly positive, but suggested the need for a testing protocol. To explore various survey methodologies, a large-scale case study was conducted on U.S. HWY 52 in Minnesota using the rolling density meter (RDM), a commercially available device developed specifically for air void analysis in asphalt pavements. The lessons learned from the SHRP2 studies and initial Minnesota pilot projects were used on a full coverage trial implementation. The full coverage trial allowed for determination of the potential of the technology for improved QA/QC and resulted in development of best practice recommendations. This paper illustrates information provided by the full coverage data and outlines recommendations related to survey coverage, data file standardization and organization, verification of location and GPR measurements, and a rigid core collection procedure. The application of these recommendations allow an RDM crew to collect valuable relative compaction data for real time feedback without interfering with paving operations or traffic closures. Additionally, core calibration can be performed after surveying to convert data to air void content and project data analysis can be used to determine the construction practices most crucial to achieving sufficient compaction.

8 November 2010
Verified
Conference Paper
Closed access
MWMark J. Watson
Mark J. Watson
JMJames McGraw
James McGraw
EJEddie Johnson
Eddie Johnson
DLDave Linell
Dave Linell
SDShongtao Dai
Shongtao Dai
Rises in construction and asphalt binder costs, as well as the growing pressures on landfills, have contributed to the increased use of Recycled Asphalt Shingles (RAS) in Hot Mixed Asphalt (HMA) Pavement Mixtures. Initial incorporation of Manufacturers Waste Scrap Shingles (MWSS) into HMA pavements yielded encouraging results and prompted waste management organizations, industry and government to investigate incorporation of Tear-Off Scrap Shingles (TOSS). As of 2009, the Minnesota Department of Transportation (Mn/DOT) standard specifications only allowed a 5% MWSS replacement for the allowable Recycled Asphalt Pavement (RAP) and TOSS was permitted, only with, "prior approval from the engineer". This need to get approval greatly reduced the willingness of local entities to use TOSS. Furthermore, a high-profile, pre-mature, and expensive, pavement failure prompted many to re-evaluate the benefits of using RAS in HMA pavement mixtures. A multi-agency research effort between Mn/DOT and the Minnesota Pollution Control Agency (MPCA) was initiated with the goal of making a recommendation on a comprehensive RAS specification, including the option of using TOSS that would allow agencies to realize the economic and environmental benefits without compromising pavement performance or durability. The research study (1) incorporated both controlled laboratory experiments and evaluations of in service pavements. Several producers submitted their ground RAS samples to the Mn/Dot laboratory for inclusion in the study. These RAS samples were tested for gradation, and deleterious materials (DM) content; these results were later used to assist in the development of an initial specification. In addition, the RAS samples were tested for the performance grade (PG) of the asphalt binder. Laboratory-produced HMA mixtures incorporating: Tear-Off Scrap Shingles (TOSS), or Manufacturer Waste Scrap Shingles (MWSS), and/or Recycled Asphalt Pavement (RAP) were tested for both asphalt binder PG grades and mixture dynamic modulus. It was concluded that the shingle properties, especially the fineness of the grind, and shingle type and the amount of recycled materials used in the HMA mixture had an impact on pavement performance. The knowledge gained from the collaborative research effort helped decision makers make an informed decision on a 2010 comprehensive RAP/RAS specification, which now allows the use of TOSS as a substitute for the total RAP content of the mix.

1 June 2017
Verified
Conference Paper
Closed access
SDShongtao Dai
Shongtao Dai
KHKyle Hoegh
Kyle Hoegh
Stripping between hot mix asphalt layers can cause premature failure of pavements. Knowledge of the lateral location, depth and extent of stripping can affect the timing and type of pavement preservation, maintenance, or rehabilitation. Since subsurface stripping extent is important for maintaining the road network, Minnesota Department of Transportation (MnDOT) uses forensic measures such as coring to make this evaluation typically. The destructive nature and lack of coverage provided by this accepted method makes finding nondestructive methods for detecting stripping of in-situ asphalt pavements an important need for MnDOT and many other agencies in the National Road Research Alliance (NRRA). The case study presented in this paper uses a DX1821 antenna to collect data at a frequency step of 20 MHz ranging from 50 MHz to 3050 MHz with a dwell time of 7.52 μs using a GeoScope Mk IV control unit on a full-scale asphalt pavement constructed on a National Center for Asphalt Technology (NCAT) test track with built-in stripping. Signals from the known stripped and non-stripped locations were used to evaluate statistical and energy based approaches. It is shown that a maximum energy ratio method, an approach that has been successfully applied to acoustic emission applications in the past, can improve signal clarity for stripping detection using ground penetrating radar. The results are demonstrated in the ability to enhance the stripping indicators in both traditional impulse time-history data and C-scan depth slices when applied to step-frequency ground penetrating radar data. The effectiveness of the energy ratio-based method in detecting fabricated stripping makes it a promising method for scoping pavement projects for construction activities. By identifying the presence and extent of stripping, road owners will have information that can allow them to avoid misapplication of preservation techniques that do not address the root stripping problem thus minimizing premature failures, or avoid major rehabilitation in situations where the evaluated lack of stripping suggests a preservation or less costly alternative can be applied.

26 August 2026 in Transportation Research Record: Journal of the Transportation Research Board
Verified
Journal Article
Closed access
STSadek Tormos
Sadek Tormos
JVJoseph Voels
Joseph Voels
EDEshan Dave
Eshan Dave
JSJo Sias
Jo Sias
SMShubham H. Modi
Shubham H. Modi
SDShongtao Dai
Shongtao Dai
Low-temperature cracking is a significant distress for asphalt pavements in cold climates. To evaluate the low-temperature cracking resistance of asphalt mixtures, the Semi-Circular Bending (SCB) and the Disk-shaped Compact Tension (DCT) tests are commonly used. However, both tests have their limitations. These include the relatively short ligament length and long testing duration in the SCB, and the complexity of specimen preparation associated with DCT. Moreover, both tests require low-temperature conditioning, which further increases testing time and costs. This study investigates the Simplified Wedge Splitting Test (SWST), designed to evaluate the low-temperature cracking potential of asphalt mixtures. This test aims to use gyratory compacted specimens prepared with minimal cutting effort, while ensuring a sufficient fracture ligament. It also aims to replace the low-temperature conditioning with a faster loading rate at room temperature through Time-Temperature Superposition Principle (TTSP). To this end, SWST experiments were conducted using different ligament lengths and loading rates, and a Finite Element (FE) model was developed with a cohesive zone fracture model to numerically evaluate the SWST test parameters. Experimentally determined SWST fracture properties show sensitivity to the fracture ligament length, with modeling results identifying 75 mm ligament length as optimal. FE modeling at different loading rates shows that linear viscoelasticity cannot fully capture the effect of loading rate on asphalt fracture, limiting the ability of TTSP to provide the required temperature-loading rate correlations. Thereafter, a framework with initial TTSP correction factors is proposed based on the modeling results.