5 October 2016 in Nature Communications
For decades it has been debated whether the conversion of synthesis gas to methanol over copper catalysts is sensitive or insensitive to the structure of the copper surface. Here we have systematically investigated the effect of the copper particle size in the range where changes in surface structure occur, that is, below 10 nm, for catalysts with and without zinc promotor at industrially relevant conditions for methanol synthesis. Regardless of the presence or absence of a zinc promotor in the form of zinc oxide or zinc silicate, the surface-specific activity decreases significantly for copper particles smaller than 8 nm, thus revealing structure sensitivity. In view of recent theoretical studies we propose that the methanol synthesis reaction takes place at copper surface sites with a unique configuration of atoms such as step-edge sites, which smaller particles cannot accommodate.
20 November 2018 in ACS Nano
Ag29 nanoclusters capped with lipoic acid (LA) can be doped with Au. The doped clusters show enhanced stability and increased luminescence efficiency. We attribute the higher quantum yield to an increase in the rate of radiative decay. With mass spectrometry, the Au-doped clusters were found to consist predominantly of Au1Ag28(LA)123-. The clusters were characterized using X-ray absorption spectroscopy at the Au L3-edge. Both the extended absorption fine structure (EXAFS) and the near edge structure (XANES) in combination with electronic structure calculations confirm that the Au dopant is preferentially located in the center of the cluster. A useful XANES spectrum can be recorded for lower concentrations, or in shorter time, than the more commonly used EXAFS. This makes XANES a valuable tool for structural characterization.
17 January 2023 in Advanced Optical Materials
Narrower band red and green emission in phosphor‐converted white light‐emitting diodes (wLEDs) can improve the efficacy and color gamut in lighting and display applications. A promising luminescent ion is Mn2+ that can have both narrowband green (tetrahedral coordination) and red (octahedral coordination) emission. Unlike in earlier lighting applications of Mn2+ phosphors, temperature quenching is important in wLEDs. Insight into the thermal quenching behavior of Mn2+ luminescence is lacking. Here systematic research is reported for a variety of Mn2+‐doped phosphors; a huge variation in the luminescence quenching temperature T50, ranging from 50 K for Mn2+ in ZnTe to 1200 K in MgAl2O4, is revealed. The value T50 shows a positive correlation with the bandgap of the host, but no correlation with the full width half maximum (FWHM) of the emission band, indicating that thermally activated photoionization, not thermal crossover, is the operative quenching mechanism. This is confirmed by thermally stimulated luminescence (TSL) measurements that show a rise in TSL signal following photoexcitation at temperatures around T50 providing evidence that quenching is correlated with generation of free charge carriers. Based on these findings, as a design rule is obtained that for temperature‐stable Mn2+ luminescence in (high power) LEDs a wide‐bandgap host material is required.
19 June 2020 in Light: Science & Applications
Lanthanide-based photon-cutting phosphors absorb high-energy photons and ‘cut’ them into multiple smaller excitation quanta. These quanta are subsequently emitted, resulting in photon-conversion efficiencies exceeding unity. The photon-cutting process relies on energy transfer between optically active lanthanide ions doped in the phosphor. However, it is not always easy to determine, let alone predict, which energy-transfer mechanisms are operative in a particular phosphor. This makes the identification and design of new promising photon-cutting phosphors difficult. Here we unravel the possibility of using the Tm3+/Yb3+lanthanide couple for photon cutting. We compare the performance of this couple in four different host materials. Cooperative energy transfer from Tm3+to Yb3+would enable blue-to-near-infrared conversion with 200% efficiency. However, we identify phonon-assisted cross-relaxation as the dominant Tm3+-to-Yb3+energy-transfer mechanism in YBO3, YAG, and Y2O3. In NaYF4, in contrast, the low maximum phonon energy renders phonon-assisted cross-relaxation impossible, making the desired cooperative mechanism the dominant energy-transfer pathway. Our work demonstrates that previous claims of high photon-cutting efficiencies obtained with the Tm3+/Yb3+couple must be interpreted with care. Nevertheless, the Tm3+/Yb3+couple is potentially promising, but the host material—more specifically, its maximum phonon energy—has a critical effect on the energy-transfer mechanisms and thereby on the photon-cutting performance.
14 November 2016 in Nanoscale
Bleaching of luminescent Ag29 clusters results in non-luminescent polydisperse species. Upon reduction of bleached clusters, optical properties of the cluster are recovered.
19 November 2018 in The Journal of Physical Chemistry C
MDMario Ulises Delgado-Jaime
Mario Ulises Delgado-Jaime
+1
The current understanding of the synthesis mechanisms of noble metal clusters is limited, in particular for Ag clusters. Here, we present a detailed investigation into the synthesis process of atomically monodisperse Ag29 clusters, prepared via reduction of AgNO3 in the presence of dithiolate ligands. Using optical spectroscopy, mass spectrometry and X-ray spectroscopy, it was determined that the synthesis involves a rapid nucleation and growth to species with up to a few hundred Ag atoms. From these larger species, Ag29 clusters are formed and their concentration increases steadily over time. Oxygen plays an important role in the etching of large particles to Ag29. No other stable Ag cluster species are observed at any point during the synthesis.