26 April 2021 in IEEE Transactions on Robotics
This article presents an active ball joint mechanism (ABENICS) enhanced by interactions of spherical gears. The gear-based joint drives three rotational degrees of freedom (RDoF) without slippage. The capabilities were inspired by the unique interactions between two different innovative gears [the cross spherical gear (CS-gear) and monopole gear (MP-gear)] and the superimposition of those interactions by the CS-gear's quadrature spherical tooth structure. One MP-gear constrains two of the three RDoF of the CS-gear. The driving module which drives the MP-gear converts this “constraint” into a “drive” and drives the CS-gear with two RDoF. The CS-gear orthogonally superimposes the interactions caused by two MP-gears to achieve three RDoF driving forces. The principle was revealed by analyzing an equivalent linkage modeled on the mechanism of ABENICS. The linkage also led to the kinematics and torque equations. The theory and physical characteristics of ABENICS were verified in comprehensive and continuous positioning experiments on manufactured prototypes. The flexibility of the actuator placement was also verified in different configurations of the driving modules. The active ball joint, ABENICS can transmit high torque and reliable positioning in three RDoF without an orientation sensor, which applies to robot joints and orientation control mechanisms.
6 September 2024 in IEEE Robotics and Automation Letters
This letter introduces a balloon pin-array gripper combining shape adaptability to various objects, stable holding by multipoint contact, and isotropic grasping performance. This is particularly useful when the shape or position of the objects cannot be accurately determined because of sensor limitations. This gripper has multiple pins whose tips are covered by flexible balloons. The gripper can adapt to the shapes of objects in two steps: axial sliding of the pins and radial inflation of the balloons. This study focuses on the effect of the layout of pins on grasping and proposes a simulation model to quantify the characteristics of each layout. Simulations showed that the concentric layout enables stable grasping by ensuring many pins contact the object, regardless of misalignment. Experiments using a prototype gripper demonstrated a trend consistent with the simulation results, proving the validity of the simulation model.
10 November 2022 in IEEE Robotics and Automation Letters
Inflatable structures used in soft robotics applications have unique characteristics. In particular, the tip-extension structure, which extends the structure from its tip, can grow without creating friction with the environment. However, these inflatable structures need high pressure to maintain their stiffness under various conditions. Excessive inner pressure limits their application in that it prevents the structure from maintaining its curved shape and from complying with specifications. This study aimed to simultaneously lower the pressure and increase the rigidity of the structure. Our work resulted in the proposal of a mechanism that combines a skeleton structure consisting of multi-joint links with functions to increase the rigidity. Insertion of this mechanism into an inflatable structure obviates the need for high inner pressure, yet enables the structure to bend and maintain the intended shape. We devised a design based on rigid articulated links and combined it with a membrane structure that utilizes the advantages of the tip-extension structure. The experimental results show that the payload of the structure designed to operate at low pressure increases compared to that of the membrane-only structure. The findings of this research can be applied to long robots that can be extended into open space without drooping and to mechanisms that enable structures to wrap around the human body.
6 January 2023 in IEEE Robotics and Automation Letters
Studies on soft robotics have explored mechanisms for switching the stiffness of a robot structure. The hybrid soft-rigid approach, which combines soft materials and high-rigidity structures, is commonly used to achieve variable stiffness mechanisms. In particular, the positive-pressurization method has attracted significant attention in recent years as it can eliminate the constraints on driving pressure. Moreover, it can change the shape holding force according to internal pressure. In this study, a variable stiffness mechanism, comprising 3-axis rotary ball joints and a single chamber, was devised via frictional force using positive pressure. The prototype can change joint angles arbitrarily when no pressure is applied and can hold joint angles when positive pressure is applied. Using a theoretical model of the torque required to hold the joint angle, we simulated the holding torque using finite element modeling analysis and measured the holding torque in the pitch and roll directions when internal pressure was applied. Based on the interaction of the theoretical model, measurement, and FEM analysis, it was confirmed that the value of the holding torque in the roll direction was approximately π/2 times larger than that in the pitch direction for each value of the internal pressure. Further, we evaluated the FEM value, theoretical value, and measured value of the holding torque by performing pairwise numerical comparisons. Our approach will aid the design of effective stiffening mechanisms for soft robotics applications.
1 February 2022 in IEEE Robotics and Automation Letters
Recently, soft robotics research has focused on mechanisms to control the stiffness of robot structures. There are several types of variable stiffness mechanisms that can change the stiffness of such structures by altering friction force. Among these, the negative-pressurization method applies negative pressure to the particles or layers that are filled inside a bag so that they contact each other and increase stiffness. However, the maximum driving pressure that can be achieved using the negative-pressurization method is 0.1 MPa, which limits the stiffness. In this study, we devised a new fluid-driven mechanism that can change the stiffness through positive pressurization using pneumatic artificial muscles. The proposed structure constructed with hollow beads and inner muscles can hold arbitrary joint angles by the contraction force generated when a pressure is applied. We measured the torque in the pitch direction due to friction when the internal pressure and inner segment diameter were changed. We confirmed that the error between the measured and theoretical torque value was within a 20% at any inner diameter. Also, since a pneumatic artificial muscle is enclosed inside the structure, an actuation effect can occur when the pressure is applied. We measured the restoring angle and force of this effect when the valve opening ratio and inner segment diameter were changed. We confirmed the function that can change the shape restoration characteristics by changing the flow rate with a single rubber tube. Our approach will help design effective stiffening mechanisms using positive pressurization in soft robotics applications. In future, we will design a tensioner mechanism for arbitrarily changing the distance of segments in the axial direction, and we will investigate the holding torque, restoring angle and force when the distance of the segments is changed.
18 March 2020 in Advanced Robotics
We present a new transporting device, the omnidirectional transporting table that exhibits a driving mechanism with two perpendicular degrees of freedom based on gear meshing. By implementing omnidirectional driving gear, it can simultaneously drive multiple carried objects (driven units) with different trajectories despite the fixed installation of the actuators to the ground frame. Since the top plate acts as the supporting mechanism for the driven units and the driven unit can pass from one driving spur gear to another, the driven unit range of motion is unlimited. This device also features intrinsic safety for human workers. In particular, because its driven mechanism is based on gear meshing, the driven unit can be positioned without a global positioning sensor. We established the control algorithm by modeling the mechanism of the device and produced a prototype. Results of path tracking and positioning accuracy experiments confirm that the control model and control algorithm are reasonable and that many specifications from the mechanism are realized. With its unique characteristics, the omnidirectional transporting table is very useful as a flexible production line in applications like multi-product, low-volume manufacturing because of its high affinity with cell production systems and industrial robots.