Konstantin N. Rozanov

Konstantin N. Rozanov

Auto-generated profile, based on publicly available information

Konstantin N. Rozanov

Russian Academy of Sciences

Research Focus & Metrics

Academic Career Length

18Years (2009-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2017 in Journal of Alloys and Compounds
Verified
Journal Article
Closed access
SMSergey S. Maklakov
Sergey S. Maklakov
ALAndrey N. Lagarkov
Andrey N. Lagarkov
YAYulia A. Adamovich
Yulia A. Adamovich
DPDmitry A. Petrov
Dmitry A. Petrov
KRKonstantin N. Rozanov
Konstantin N. Rozanov
DFDmitry S. Filimonov
Dmitry S. Filimonov

1 January 2009 in Progress In Electromagnetics Research
Verified
Journal Article
Closed access
PDF file
SSSergey Nickolaevich Starostenko
Sergey Nickolaevich Starostenko
KRKonstantin N. Rozanov
Konstantin N. Rozanov
The efiect of magnetic bias on dielectric spectra of composite sheets fllled with Fe or Co-based microwires is studied experimentally and via simulation. The permittivity is measured using a free-space technique within the frequency band from 6 to 12GHz. The bias is applied either parallel or perpendicular to the microwave electric fleld; the bias strength varies from 0 to 2.5kOe. The composites with Fe-based wires reveal a single region of bias dependent permittivity under bias about 800{1000Oe. The composites with Co- based wires reveal two such regions: the high-fleld region is close to that of composites with Fe wires, and the low-fleld region corresponds to the coercive fleld of Co wires (2{3Oe). The high-fleld efiect is related to the dependence of ferromagnetic resonance (FMR) parameters on bias; the low-fleld efiect is related to the rearrangement of the domain structure of Co-based wires. The interference of magnetoimpedance and dipole resonance is analyzed, revealing the efiects ofi wire length, diameter, parameters of magnetic resonance and composite structure. The results are considered in view of application to the problem of controlled microwave attenuation. Simulation shows that the narrower is the FMR spectrum and the higher is the admissible loss of a sheet in a transparent state, the wider is the dynamic range of attenuation control. The attenuation range of a lattice of continuous wires is smaller than that of a screen with identical wire sections, where the magnetoimpedance efiect is amplifled resonantly. At 15GHz frequency the strength of the bias switching opaque sheet with Fe-based wires to the transparent state is about 2000Oe. For 3dB admissible loss, the range of attenuation control about 10dB is feasible in a composite with aligned wire sections. If the aligned sections are distributed regularly, the loss in a transparent state is about 1dB lower.

30 April 2009 in Technical Physics
Verified
Journal Article
Closed access
PDF file
EEE. P. Elsukov
E. P. Elsukov
KRK. N. Rozanov
K. N. Rozanov
SLS. F. Lomaeva
S. F. Lomaeva
AOA. V. Osipov
A. V. Osipov
DPD. A. Petrov
D. A. Petrov
DSD. V. Surnin
D. V. Surnin
The structure and microwave magnetic properties of Fe powders grounded in argon or acetone and also of Fe-Si-C and amorphous Fe-Co-Si-C powders mechanically alloyed in argon are studied using X-ray diffraction, Mössbauer spectroscopy, granulometric and microscopic analyses, magnetostatic measurements, and microwave spectroscopy. The goal of investigation is to determine the influence of factors (shape, size, and chemical and phase compositions of grains) governing the microwave material parameters of composites based on these alloys in the frequency range 0.1–3.0 GHz. It is shown that the difference in the grain shape is the basic reason for the difference in the microwave permeability at low frequencies (3 GHz or lower). At higher frequencies, the magnetic properties are related to the skin effect and depend largely on the grain size. The differences in the microwave properties of the composites are not significant and are concealed by the above effects.

1 January 2009 in Progress in Electromagnetics Research C
Verified
Journal Article
Closed access
PDF file
SSSergey Nickolaevich Starostenko
Sergey Nickolaevich Starostenko
KRKonstantin N. Rozanov
Konstantin N. Rozanov

1 July 2017 in Inorganic Materials: Applied Research
Verified
Journal Article
Closed access
PDF file
SLS. F. Lomaeva
S. F. Lomaeva
AMA. N. Maratkanova
A. N. Maratkanova
DPD. A. Petrov
D. A. Petrov
KRK. N. Rozanov
K. N. Rozanov
SSS. N. Starostenko
S. N. Starostenko
Structural and phase composition and magnetostatic and microwave properties of Fe70Co30–SiO2 systems obtained by high-energy milling in acetone for different times (from 6 to 48 h) are studied. It is found that, after the longest milling time, the obtained particles have sizes from 0.5 to 5 μm, are covered with a thin layer of SiO2, and contain 10 wt % iron carbides. Milling-induced change in the phase composition of the particles influences their specific magnetization of saturation and coercive force, but has a small effect on the microwave permittivity of composite materials containing these particles in the frequency range of 0.1–6 GHz. As the milling time grows, the imaginary part of the microwave permeability decreases at frequencies below 1 GHz.

4 July 2018 in EPJ Web of Conferences
Verified
Journal Article
Open access
SBStanislav Y. Bobrovskii
Stanislav Y. Bobrovskii
VGVictor A. Garanov
Victor A. Garanov
ANAndrei S. Naboko
Andrei S. Naboko
AOAlexei V. Osipov
Alexei V. Osipov
KRKonstantin N. Rozanov
Konstantin N. Rozanov
Frequency dependencies of permittivity and permeability of composites filled with Permalloy powder with various concentrations and shapes of particles have been measured and discussed. The powder particles of various shapes were obtained by mechanical milling of industrial Permalloy powder in organic media. Paraffin wax was used as a matrix for producing the composites. A shape data of the particles was obtained with an electron microscope. The permittivity and permeability were measured in the frequency range of 0.13 to 10 GHz. The shape of the particles changes from sphere to platelet with increase of milling time. The change leads to a shift of the ferromagnetic resonance (FMR) frequency and magnetic loss peak. It is shown that for larger particles, a decrease of the Q-factor of the ferromagnetic resonance is observed, which is explained by the strong influence of the skin effect. With increase of the concentration of the Permalloy particles in composite, the magnetic loss peak shifts to low frequencies. When the spherical particles are flattened, the resonance frequency shifts to high frequencies, which indicates that the shift to high frequencies due to the decrease of the skin effect and the change in the magnetic structure is stronger than the shift to the low frequencies by changing the shape and reducing the demagnetization.