Wenkai Li

Wenkai Li

Auto-generated profile, based on publicly available information

Wenkai Li

Beijing Materials Handling Research Institute CO., LTD. 3 , Beijing 100007

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
6 October 2023 in Materials Today Communications
Verified
Journal Article
Closed access
WZWenjun Zhang
Wenjun Zhang
CXChunguang Xu
Chunguang Xu
WLWenkai Li
Wenkai Li
BYBo Yang
Bo Yang

1 March 2024 in AIP Advances
Verified
Journal Article
Open access
PDF file
WLWenkai Li
Wenkai Li
CXChunguang Xu
Chunguang Xu
WZWenjun Zhang
Wenjun Zhang
SLShiyuan Liu
Shiyuan Liu
PYpeng yin
peng yin
By applying ultrasonic treatment to ZL205A aluminum alloy melt containing different Cd contents and then using a tensile test, a scanning electron microscope experiment, and a metallographic experiment, the influence of ultrasonic treatment to ZL205A aluminum alloy melt on the properties of aluminum–copper alloy with different Cd contents in the liquid phase high-temperature region was studied. The effect of ultrasonic treatment on the solidification structure of ZL205A aluminum alloy was investigated. The results showed that there was no significant difference in the form of Cd and the solid solution rate of the aluminum alloy with different Cd contents in ultrasonic-assisted casting. However, the effect of ultrasonic waves on the high-temperature liquid phase of the melt of ZL205A aluminum alloy can effectively reduce the porosity defects in the solidification structure of the casting, refine the solidification structure, and make the structure more uniform. The ultrasonic cavitation effect can promote the formation and uniform distribution of Al–3Ti and improve the nucleation rate, and the effect can continue after heat treatment. This can solve the problem that increasing Cd content in ZL205A greatly reduces the toughness of castings while increasing the strength. The sample with a Cd content of 0.20% and with ultrasonic treatment has the highest strength, the average tensile strength is 475.5 MPa, and the yield strength is 381.75 MPa. However, compared with the conventional casting samples with the same Cd content, the decrease in elongation was significantly reduced.

26 July 2024 in Journal of Testing and Evaluation
Verified
Journal Article
Closed access
PDF file
WLWenkai Li
Wenkai Li
GZGuowei Zou
Guowei Zou
PYpeng yin
peng yin
CXChunguang Xu
Chunguang Xu
WZWenjun Zhang
Wenjun Zhang
CZCongbin Zhu
Congbin Zhu
AISI 304 stainless steel has low thermal conductivity and a high linear expansion coefficient; conventional welding with this material produces coarse grains and poor joint tensile properties. To address the problems inherent in conventional 304 stainless steel welding, an ultrasonic transducer was brought into contact with a base metal and treated with ultrasonic vibration during welding. The residual stress distribution, microstructure, and mechanical properties of the welded joint were then analyzed. The results showed that under the combined action of thermodynamics and the dynamics caused by ultrasonic treatment, the flow performance of the molten pool was enhanced, heat was transferred from the high-temperature region to the low-temperature region, and the metal elements were constantly diffused during the crystallization of the molten pool. Thus, the transformation rate of columnar crystals to equiaxed crystals was accelerated, the proportion of equiaxed crystals increased, and the grains became refined. Compared with conventional welding, the microstructure of the 304 stainless steel welded joints was better after the introduction of ultrasonic vibration, and its tensile residual stress was significantly lower. The improvement in the microstructure of the weld improved its mechanical properties, and the hardness of the weld zone increased significantly, which was close to that of the base metal. After the ultrasonic treatment, the increase in the equiaxed crystals and the refinement in the grains effectively improved the quality of the welded joints so that the tensile strength of the welded joints was higher than that of conventional welded joints. Under the condition of the same ultrasonic vibration frequency and power, the tensile strength of welded joints with 2-mm steel plate exhibited a notable increase, which was 13 %.

1 December 2025 in APL Materials
Verified
Journal Article
Open access
PYpeng yin
peng yin
CXChunguang Xu
Chunguang Xu
WLWenkai Li
Wenkai Li
ZWZekai Wang
Zekai Wang
THTingting Hao
Tingting Hao
LWLin Wang
Lin Wang
To address the issues of significant deformation, high residual stress, and poor joint performance in the conventional welding process of 2219 aluminum alloy, this paper constructs an ultrasonic-assisted TIG welding system. This system employs high-frequency ultrasonic excitation coupled with the welding process to improve the microstructure and enhance the overall mechanical properties. By utilizing a variety of characterization techniques, such as x-ray, three-dimensional deformation measurement, ultrasonic stress measurement, microstructure observation, and mechanical property testing, we systematically analyze the influence patterns of acoustic energy input on the microstructure and macroscopic properties of welded joints. The results revealed that, in comparison with conventional TIG welding, the ultrasonic-assisted welding process reduces component deformation. It increases the tensile strength of the joint by ∼34%, improves elongation by 68%, and enhances the impact toughness of the weld zone (WZ) and heat-affected zone (HAZ) by 14% and 36%, respectively. Moreover, it decreases the peak residual stress by around 35%, improves corrosion resistance, and raises the average microhardness by ∼10%. This study offers a theoretical foundation and technical approach for ultrasonic welding of aluminum alloy thick plates, expanding the engineering application potential of ultrasonic technology in high-end manufacturing sectors.