Nano-catalysts containing copper–cobalt oxides (Cu–Co–O) have been synthesized by the citric acid (CA) complexing method. Copper (II) nitrate and Cobalt (II) nitrate were employed in different molar ratios as the starting reactants to prepare three types of nano-catalysts. Well crystalline nano-catalysts were produced after a period of 3 hours by the calcination of CA–Cu–Co–O precursors at 550 °C. The phase morphologies and crystal composition of synthesized nano-catalysts were examined using Scanning Electron Microscope (SEM), Energy Dispersive Spectroscopy (EDS) and Fourier Transform Infrared Spectroscopy (FTIR) methods. The particle size of nano-catalysts was observed in the range of 90 nm–200 nm. The prepared nano-catalysts were used to formulate propellant samples of various compositions which showed high reactivity toward the combustion of HTPB/AP-based composite solid propellants. The catalytic effects on the decomposition of propellant samples were found to be significant at higher temperatures. The combustion characteristics of composite solid propellants were significantly improved by the incorporation of nano-catalysts. Out of the three catalysts studied in the present work, CuCo-I was found to be the better catalyst in regard to thermal decomposition and burning nature of composite solid propellants. The improved performance of composite solid propellant can be attributed to the high crystallinity, low agglomeration and lowering the decomposition temperature of oxidizer by the addition of CuCo-I nano-catalyst
28 May 2014 in Propellants, Explosives, Pyrotechnics
The chemical electrolytes are widely used in electrochemical machining (ECM) and have a significant effect on both the material removal rate (MRR) and the surface finish (Ra) of the workpiece. The process parameters of ECM, such as current density, electrolyte composition, and feed rate, are vital for optimizing machining performance. Research has indicated that high current density can create localized non-conductive passivating films, which impede metal dissolution. In this study, the aqueous solution of sodium nitrate (NaNO3) combined with gold nanoparticles (AuNPs) has been used as a novel electrolyte to evaluate the machining performance of the 20MnCr5 steel alloy. The inclusion of AuNPs in the NaNO3 solution enhanced local surface effects and promoted low-valence metal dissolution. The results demonstrated that the MRR and average surface roughness of the 20MnCr5 workpiece improved by 19.6% and 35.5%, respectively, when AuNPs were utilized compared to the alone NaNO3 electrolytic system. The experimental results also showed that the MRR increased within the current density range of 5.5 A/cm2 to 15.8 A/cm2, but declined in the range of 15.8 A/cm2 to 32.5 A/cm2. This decrease in the MRR at higher current densities can be attributed to the formation of non-conductive metal oxide passive layers. The oxygen evolution reaction (OER) was observed with the NaNO3 electrolyte at higher current densities, resulting in the formation of numerous micropores on the surface of the workpiece. In contrast, when the electrolyte was combined with AuNPs, these micropores ruptured quickly, creating new sites for the re-dissolution of metal ions. The microstructural changes on the machining surfaces under different operating conditions were analyzed using field emission scanning electron microscopy (FESEM), and the results are presented. Possible surface reactions, such as the formation of metal oxides and the release of oxygen gas, are discussed based on energy-dispersive X-ray (EDX) analysis and cyclic voltammetry (CV) studies.
The growth of spherulitic crystal patterns in a Belousov–Zhabotinski (BZ) type reaction system by using acetyl acetone (AA)–succinic acid (SA) as dual organic substrates has been reported. The reaction system in the liquid phase has been found to show concentric ring-like wave patterns. A colloidal phase composed of numerous fine particles has also been observed during reaction. The solid phase nucleation has been found to occur in the colloidal phase, which leads to the formation of some stable nucleus centers. The solid phase nucleus has been found to grow in symmetric crystal patterns, with the progress of reaction, exhibiting spherulitic morphology. The possible growth behavior of spherulites has also been discussed. The spherulitic structure composed of fine crystal fibrils diverging from a common center have been observed by a scanning electron microscopy (SEM) technique. The polymorphic crystalline phase, found in spherulites has been supported by thermal characterization (TGA/DTA) and X-ray diffraction (XRD) patterns of crystal materials.