6 March 2023 in Journal of Fluid Mechanics
When a liquid drop falls on a solid substrate, the air layer between them delays the occurrence of liquid–solid contact. For impacts on smooth substrates, the air film can even prevent wetting, allowing the drop to bounce off with dynamics identical to that observed for impacts on superamphiphobic materials. In this paper, we investigate similar bouncing phenomena, occurring on viscous liquid films, that mimic atomically smooth substrates, with the goal to probe their effective repellency. We elucidate the mechanisms associated with the bouncing to non-bouncing (floating) transition using experiments, simulations, and a minimal model that predicts the main characteristics of drop impact, the contact time and the coefficient of restitution. In the case of highly viscous or very thin films, the impact dynamics is not affected by the presence of the viscous film. Within this substrate-independent limit, bouncing is suppressed once the drop viscosity exceeds a critical value, as on superamphiphobic substrates. For thicker or less viscous films, both the drop and film properties influence the rebound dynamics and conspire to inhibit bouncing above a critical film thickness. This substrate-dependent regime also admits a limit, for low-viscosity drops, in which the film properties alone determine the limits of repellency.
4 June 2021 in Journal of Fluid Mechanics
Thin, viscous liquid films subjected to impact events can deform. Here we investigate free-surface oil-film deformations that arise owing to the build up of air under the impacting and rebouncing of water drops. Using digital holographic microscopy, we measure the three-dimensional surface topography of the deformed film immediately after the drop rebound, with a resolution down to 20 nm. We first discuss how the film is initially deformed during impact, as a function of film thickness, film viscosity and drop impact speed. Subsequently, we describe the slow relaxation process of the deformed film after the rebound. Scaling laws for the broadening of the width and the decay of the amplitude of the perturbations are obtained experimentally and found to be in excellent agreement with the results from a lubrication analysis. We finally arrive at a detailed spatio–temporal description of the oil-film deformations that arise during the impact and rebouncing of water drops.
22 August 2022 in Journal of Fluid Mechanics
We investigate the leading-edge separation, also called negligible boundary-layer thickness separation, induced by an impinging shock on a sharp flat plate. The canonical impinging shock wave/boundary-layer interaction configuration consisting of a wedge and a plate wall, placed in hypersonic free stream, is used for the investigations. We first construct a theoretical model for the leading-edge separated flow field (LESF) which predicts separation bubble geometry and surface pressure distribution as a function of three parameters: free-stream Mach number, wedge angle and the reattached flow turning angle. Markedly different predictions of the separated flow field are obtained for an oblique and a near normal reattachment on the plate surface. Experiments in a shock tunnel at a nominal Mach , are used to validate the model. Schlieren flow visualization using a high-speed camera and surface pressure measurements using fast response piezoelectric sensors are the diagnostics employed. For a range of shock impingement locations, the LESFs are observed to be geometrically similar and in good agreement with the LESF model. When the impingement location gets closer to the leading edge, it is observed from experiments that the flow field is no longer geometrically similar, and the separation angle increases as the impingement gets closer to the leading edge beyond the range of similarity. The work thereby offers an elaborate description of the leading-edge separated flow when shock impingement occurs near the plate leading edge.
16 November 2022 in arXiv
When a liquid drop falls on a solid substrate, the air layer in between them delays the occurrence of liquid--solid contact. For impacts on smooth substrates, the air film can even prevent wetting, allowing the drop to bounce off with dynamics identical to that observed for impacts on superamphiphobic materials. In this article, we investigate similar bouncing phenomena, occurring on viscous liquid films, that mimic atomically smooth substrates, with the goal to probe their effective repellency. We elucidate the mechanisms associated to the bouncing to non-bouncing (floating) transition using experiments, simulations, and a minimal model that predicts the main characteristics of drop impact, the contact time, and the coefficient of restitution. In the case of highly viscous or very thin films, the impact dynamics is not affected by the presence of the viscous film. Within this substrate--independent limit, bouncing is suppressed once the drop viscosity exceeds a critical value as on superamphiphobic substrates. For thicker or less viscous films, both the drop and film properties influence the rebound dynamics and conspire to inhibit bouncing above a critical film thickness. This substrate--dependent regime also admits a limit, for low viscosity drops, in which the film properties alone determine the limits of repellency.