14 August 2019 in IEEE Transactions on Electron Devices
In this article, we investigate a novel technique to minimize row hammer (RH) fail in the saddle fin recessed channel access transistor (S-RCAT) at 1X dynamic random access memory node. We propose a selective introduction of a low work function (WF) metal nanowire (MNW) at the gate metal/gate oxide (GOX) interface to mitigate the RH fail. Using 3-D TCAD simulations, we analyze the mechanism of the RH fail and its mitigation through the use of MNW. The improvement in RH fail is shown due to the MNW and gate-metal work-function-difference induced energy valleys (EVs) between the neighboring S-RCATs. These valleys prevent the diffusion of electrons from aggressor (accessed) to victim (not accessed) cell, which improves RH fail even in the presence of a high concentration of interface states and gate-induced-drain leakage. The introduction of MNW is found not to have any substantial effect on S-RCAT characteristics (VT, ION, or SS). Furthermore, we model the induced EV by considering the WF difference between MNW and gate metal as an effective charge. This model is shown to be in good agreement with the TCAD results. The results obtained in this study demonstrate the potential of using MNW in the gate-stack of S-RCAT for the elimination of RH fail in 1X technology nodes. This technique can also be extended for the use in other device technologies, such as NAND (cell-to-cell interference) and logic transistors.
12 May 2022 in IEEE Transactions on Electron Devices
In this article, we study the field cycling behavior of ALD-deposited ferroelectric Hf0.5Zr0.5O2 with TiN as the top and bottom electrodes on the silicon substrate. We investigate the effect of temperature on the endurance, capacitance, and leakage of the device. We observe an insignificant wake-up effect attributed to the nitrogen-rich interface between TiN and HZO film. We also report an increase in the remnant polarization, ${P}_{r}$ , with temperature initially, and the reduced rate of ${P}_{r}$ degradation in the fatigue phase at elevated temperatures. The increase in ${P}_{r}$ of the devices at elevated temperatures is attributed to the strong de-pinning. The calculated trap barrier energy of 1 eV in the fatigue phase points toward oxygen vacancy generation in the film. The lower activation energy found in the fatigue phase suggests a higher de-pinning rate for the devices. The reduced rate of ${P}_{r}$ degradation in fatigue is attributed to two-competing mechanisms: vacancy generation (leading to domain pinning) and temperature-dependent de-pinning. The results presented in this study provide key insights into degradation mechanisms that are crucial for improving the reliability of HZO films.
4 January 2021 in RSC Advances
In the current study, novel four electrode-based impedimetric biosensors have been fabricated using photolithography techniques and utilized to evaluate the cytotoxicity of tamoxifen on cervical cancer cell lines. The cell impedance was measured employing the electric cell-substrate impedance sensing (ECIS) method over the frequency range of 100 Hz to 1 MHz. The results obtained from impedimetric biosensors indicate that tamoxifen caused a significant reduction in the number of HeLa cells on the electrode surfaces in a dose-dependent manner. Next, the impedance values recorded by the fabricated biosensors have been compared with the results obtained from the different conventional techniques such as 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl tetrazolium bromide (MTT), live-dead cell assay, and flow cytometric analysis to estimate the cytotoxicity of tamoxifen. The impedimetric cytotoxicity of tamoxifen over the growth and proliferation of HeLa cells correlates well with the traditional methods. In addition, the IC50 values obtained from impedimetric data and MTT assay are comparable, signifying that the ECIS technique can be an alternative method to assess the cytotoxicity of different novel drugs. The working principle of the biosensor has been examined by scanning electron microscopy, indicating the detachment of cells from gold surfaces in a dose-dependent manner, signifying the decrease in impedance at higher drug doses.
31 July 2018 in IEEE Electron Device Letters
In this letter, we investigate row hammering (RH) in recessed channel access transistor (RCAT)-DRAM cells. A novel technique is proposed to minimize the row hammer fail in DRAM cells by selective/local introduction of metal nanoparticles (MNPs) at the gate metal–oxide interface. Using TCAD simulations, we show that the introduction of MNPs with an optimized work function (WF) significantly reduces the storage node leakage of unaccessed DRAM cells (victim cells) due to the hammered access of neighboring DRAM cells (aggressor cells) sharing a common bit line. The proposed technique potentially eliminates row hammer fail in RCAT-DRAM cells at 2X and 1X nodes. The improvement in row hammer fail is due to the dual-energy valley induced between the neighboring DRAM cells by the introduction of MNPs. These valleys prevent diffusion of electrons from the aggressor cell to the victim cell, which improves row hammer fail. This letter shows that the introduction of MNPs is a promising technique to eliminate row hammer fail in DRAM cells.
28 September 2018 in Journal of Electronic Materials
11 April 2018 in IEEE Transactions on Electron Devices
String read current (Iread) reduction with rising mold height and grain boundary traps is one of the major hurdle in the development of 3-D NAND flash memory. In this paper, we have investigated Iread with variation in polysilicon channel grain size (GS), grain boundary trap density, and channel thickness (TSi), using TCAD. We find that under a critical value of GS, Iread decreases with increase in TSi. This is attributed to the fact that with smaller GS, the total number of grain boundaries and associated traps are significantly higher. Moreover, there exists a typical value of GS for which Iread is independent of TSi, which is desirable to minimize the deviations in Iread arising from TSi variations. The resulting tradeoff in the design of more efficient 3-D NAND flash is demonstrated and discussed. Further, it is found that Iread increases significantly by limiting the polysilicon channel grain boundary trap concentration under 10¹² cm⁻². The results presented in this paper are crucial for optimizing Iread and program/erase threshold voltage (VT) window, and serve as key guidelines in the design of 3-D NAND flash memory with better performance.