18 January 2018 in IEEE Transactions on Instrumentation and Measurement
WFWaldemar C. Leite Filho
This paper presents an innovative in-field coarse bias estimation (CBE) method for stationary intermediate-grade inertial measurement units (IMUs), which is based on the existence of normality and orthogonality errors in the attitude matrix supplied by the traditional three-axis attitude determination stationary coarse alignment (CA) stage. Differently from the currently existing in-field bias estimation formulations, the proposed CBE method is conceived to be conducted in stationary conditions, jointly with the CA, and it allows the down accelerometer bias and the north and down angular rate sensor biases to be adequately estimated. As a main contribution of this paper, we demonstrate that the proposed CBE method is able to greatly accelerate the estimation process of the aforementioned biases, contributing, hence, to shorten the IMU setup time. A comprehensive error analysis is presented, and the conclusions are twofold: 1) the proposed CBE method is valid regardless of the IMU orientation and 2) its estimation accuracy is mainly constrained by the north accelerometer bias and the position location uncertainty, which are, in general, very reduced. Results from simulated and experimental test confirm the adequacy of the outlined verifications, also attesting the superiority of the proposed CBE method in situations where, due to time constraints, stationary fine alignment procedures are not allowed to be carried out.
1 July 2003 in Acta Astronautica
28 May 2013 in Mathematical Problems in Engineering
The ever-increasing use of artificial satellites in both the study of terrestrial and space phenomena demands a search for increasingly accurate and reliable pointing systems. It is common nowadays to employ reaction wheels for attitude control that provide wide range of torque magnitude, high reliability, and little power consumption. However, the bearing friction causes the response of wheel to be nonlinear, which may compromise the stability and precision of the control system as a whole. This work presents a characterization of a typical reaction wheel of 0.65 Nms maximum angular momentum storage, in order to estimate their friction parameters. It used a friction model that takes into account the Coulomb friction, viscous friction, and static friction, according to the Stribeck formulation. The parameters were estimated by means of a nonlinear batch least squares procedure, from data raised experimentally. The results have shown wide agreement with the experimental data and were also close to a deterministic model, previously obtained for this wheel. This model was then employed in a Dynamic Model Compensator (DMC) control, which successfully reduced the attitude steady state error of an instrumented one-axis air-bearing table.
14 December 2011 in Mathematical Problems in Engineering
MZMaria Cecilia F. P. S. Zanardi
Maria Cecilia F. P. S. Zanardi
The aim of this work is to test an algorithm to estimate, in real time, the attitude of an artificial satellite using real data supplied by attitude sensors that are on board of the CBERS‐2 satellite (China Brazil Earth Resources Satellite). The real‐time estimator used in this work for attitude determination is the Unscented Kalman Filter. This filter is a new alternative to the extended Kalman filter usually applied to the estimation and control problems of attitude and orbit. This algorithm is capable of carrying out estimation of the states of nonlinear systems, without the necessity of linearization of the nonlinear functions present in the model. This estimation is possible due to a transformation that generates a set of vectors that, suffering a nonlinear transformation, preserves the same mean and covariance of the random variables before the transformation. The performance will be evaluated and analyzed through the comparison between the Unscented Kalman filter and the extended Kalman filter results, by using real onboard data.
1 January 2012 in Mathematical Problems in Engineering
If three or more GPS antennas are mounted properly on a platform and differences of GPS signals measurements are collected simultaneously, the baselines vectors between antennas can be determined and the platform orientation defined by these vectors can be calculated. Thus, the prerequisite for attitude determination technique based on GPS is to calculate baselines between antennas to millimeter level of accuracy. For accurate attitude solutions to be attained, carrier phase double differences are used as main type of measurements. The use of carrier phase measurements leads to the problem of precise determination of the ambiguous integer number of cycles in the initial carrier phase (integer ambiguity). In this work two algorithms (LSAST and LAMBDA) were implemented and tested for ambiguity resolution allowing accurate real‐time attitude determination using measurements given by GPS receivers in coupled form. Platform orientation was obtained using quaternions formulation, and the results showed that LSAST method performance is similar to LAMBDA as far as the number of epochs which are necessary to resolve ambiguities is concerned, but with processing time significantly higher. The final result accuracy was similar for both methods, better than 0.1° to 0.2°, when baselines are considered in decoupled form.
7 March 2016 in Journal of Aerospace Technology and Management
MZMaria Cecília F. P. S. Zanardi
Maria Cecília F. P. S. Zanardi
Unscented Kalman Filter for Determination of Spacecraft Attitude Using Different Attitude Parameterizations and Real Data