Sergey Vladimirovich Chertovskikh

Sergey Vladimirovich Chertovskikh

Auto-generated profile, based on publicly available information

Sergey Vladimirovich Chertovskikh

Ufa State Aviation Technical University

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
4 November 2017 in Coatings
Verified
Journal Article
Open access
PDF file
JPJose Mario Paiva
Jose Mario Paiva
MSMohamed Shalaby
Mohamed Shalaby
MCMohammad Chowdhury
Mohammad Chowdhury
LSLev Shuster
Lev Shuster
SCSergey Chertovskikh
Sergey Chertovskikh
SVStephen Veldhuis
Stephen Veldhuis
Tribological phenomena and tool wear mechanisms during machining of hard-to-cut TiAl6V4 aerospace alloy have been investigated in detail. Since cutting tool wear is directly affected by tribological phenomena occurring between the surfaces of the workpiece and the cutting tool, the performance of the cutting tool is strongly associated with the conditions of the machining process. The present work shows the effect of different machining conditions on the tribological and wear performance of TiB2-coated cutting tools compared to uncoated carbide tools. FEM modeling of the temperature profile on the friction surface was performed for wet machining conditions under varying cutting parameters. Comprehensive characterization of the TiB2 coated vs. uncoated cutting tool wear performance was made using optical 3D imaging, SEM/EDX and XPS methods respectively. The results obtained were linked to the FEM modeling. The studies carried out show that during machining of the TiAl6V4 alloy, the efficiency of the TiB2 coating application for carbide cutting tools strongly depends on cutting conditions. The TiB2 coating is very efficient under roughing at low speeds (with strong buildup edge formation). In contrast, it shows similar wear performance to the uncoated tool under finishing operations at higher cutting speeds when cratering wear predominates.

1 March 2016 in Journal of Friction and Wear
Verified
Journal Article
Closed access
PDF file
LSL. Sh. Shuster
L. Sh. Shuster
RMR. F. Mamleyev
R. F. Mamleyev
RKR. R. Kamaletdinova
R. R. Kamaletdinova
SCS. V. Chertovskikh
S. V. Chertovskikh
RKR. M. Kireev
R. M. Kireev

1 January 2016 in Journal of Friction and Wear
Verified
Journal Article
Closed access
PDF file
LSL. Sh. Shuster
L. Sh. Shuster
SCS. V. Chertovskikh
S. V. Chertovskikh
BMB. Sh. Minasov
B. Sh. Minasov
RYR. R. Yakupov
R. R. Yakupov
IEI. I. Emaev
I. I. Emaev

1 December 2021 in Journal of Friction and Wear
Verified
Journal Article
Closed access
PDF file
LSL. Sh. Shuster
L. Sh. Shuster
GFG. S. Fox-Rabinovich
G. S. Fox-Rabinovich
SCS. V. Chertovskikh
S. V. Chertovskikh
The effect of cutting conditions on the tribotechnical characteristics and wear resistance of cutting tools with and without TiB2 coating during processing

17 November 2017 in Biomedical Engineering
Verified
Journal Article
Closed access
PDF file
RYR. R. Yakupov
R. R. Yakupov
BMB. Sh. Minasov
B. Sh. Minasov
LSL. Sh. Schuster
L. Sh. Schuster
ABA. R. Bilyalov
A. R. Bilyalov
SCS. V. Chertovskikh
S. V. Chertovskikh
IEI. I. Emaev
I. I. Emaev

12 July 2024 in E3S Web of Conferences
Verified
Conference Paper
Open access
PDF file
VSVladimir Semenov
Vladimir Semenov
SCSergey Chertovskikh
Sergey Chertovskikh
HLHsin Lin
Hsin Lin
The paper presents an analysis of the results of evaluating the effect of microstructure obtained by methods of severe plastic deformation (SPD) - equal-channel angular pressing (ECAP) and high-pressure torsion (HPT) - on the mechanical and operational properties of the Mg-1%Ca alloy. The influence of the ZrO2 nano-oxide coating deposited using the atomic layer deposition (ALD) technology was considered in comparison with the uncoated material under study. At the same time, it was noted that the application of a ZrO2 nano-oxide coating by the ALD method made it possible to increase the mechanical characteristics of the ECAP samples by about 20% (the ultimate strength was 205 MPa after ECAP and 262 MPa for ECAP samples with ALD coating). The lowest values of the adhesive component of the friction coefficient were observed on samples after SPD treatment using the HPT method with an applied ZrO2 nano-oxide coating. However, it was found that both the initial material of the study and after SPD treatment by ECAP, the Mg-1% Ca alloy demonstrates a slightly lower damping ability during the deposition of ZrO2 films.