Jeyakumar Rengaraj

Jeyakumar Rengaraj

Auto-generated profile, based on publicly available information

Jeyakumar Rengaraj

Department of Mechanical Engineering, Sri Krishna College of Engineering and Technology, Kuniyamuthur, Coimbatore, Tamil Nadu, India

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2017 in The International Journal of Advanced Manufacturing Technology
Verified
Journal Article
Closed access
PDF file
RJR. Jeyakumar
R. Jeyakumar
PSP. S. Sampath
P. S. Sampath
RRR. Ramamoorthi
R. Ramamoorthi
TRT. Ramakrishnan
T. Ramakrishnan

5 September 2024 in Cellulose Chemistry and Technology
Verified
Journal Article
Closed access
SKShettahalli Mantaiah Vinu Kumar
Shettahalli Mantaiah Vinu Kumar
RJRengaraj Jeyakumar
Rengaraj Jeyakumar
NMNallasivam Manikandaprabu
Nallasivam Manikandaprabu
CSChandrasekaran Sasikumar
Chandrasekaran Sasikumar
Flax reinforced epoxy (F-Ep) composites were prepared by the compression moulding technique, varying the fiber content (0, 25, 35 and 45 wt%). The free vibration test was performed on the neat epoxy and F-Ep composites to understand their dynamic characteristics, and results showed that natural frequency and damping factor of the F-Ep composites increased with an increase in the fiber content. The F-Ep composite (45F-Ep) that exhibited better damping was selected for performing the drilling operation. Factors such as spindle speed (rpm), feed rate (mm/min) and drill point angle (degree) were chosen as input parameters and the tabulated set of experiments were in accordance with Taguchi’s design of experiment. The response measured was thrust force and the obtained values were found in the range of 19.66 to 50.75 N. The minimum value of thrust force was achieved when the F-Ep composite was drilled at high spindle speed (3000 rpm), with a feed rate of 75 mm/min using the drill point angle of 118°. ANOVA analysis showed that the developed regression model was significant and thrust force was mainly influenced by the spindle speed. Mathematical models were developed for drilling F-Ep composite using response surface methodology (RSM) and adaptive neuro fuzzy inference system (ANFIS) and compared for their efficacy.

22 July 2024 in Cellulose Chemistry and Technology
Verified
Journal Article
Closed access
SKShettahalli Mantaiah Vinu Kumar
Shettahalli Mantaiah Vinu Kumar
JRJeyakumar Rengaraj
Jeyakumar Rengaraj
ESErusagounder Sakthivelmurugan
Erusagounder Sakthivelmurugan
Alkali treated Alstonia macrophylla fiber reinforced polypropylene (PP/AS) composite was fabricated using a hot compression moulding machine through the film stacking technique. The raw fiber was subjected to alkali treatment to enhance the strong interfacial adhesion with the PP matrix. Alkali treated fiber at five levels of fiber loading (10, 20, 30, 40 and 50 vol%) was used for composite fabrication. The fabricated composites were designated as Neat PP, PP10AS, PP20AS, PP30AS, PP40AS, and PP50AS, respectively. Mechanical test results conducted in accordance with the ASTM standards revealed that tensile strength, flexural strength, impact toughness of the PP/AS composites increased with an increase in fiber loading. However, beyond 40 vol% of fiber loading, mechanical properties deteriorate. Of the prepared laminates, PP40AS composite outperformed other laminates, with 20.14%, 274.2% and 314.42% improvement in the tensile strength, flexural strength, and impact strength, respectively, when compared to neat PP laminates. The moisture absorption rate increased with the increase in fiber loading, as it leads to an increment in the number of hydroxyl groups in PP/AS composites. TGA results showed that the thermal stability of the PP laminate improved upon impregnation with alkali treated fiber. The final thermal degradation temperature of the PP/AS composite increased from 437.7 °C to 445.2 °C. FESEM analysis revealed the major mechanism endured by the PP/AS specimens during mechanical failure.

7 September 2025 in Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science
Verified
Journal Article
Closed access
JRJeyakumar Rengaraj
Jeyakumar Rengaraj
VMVinu Kumar S M
Vinu Kumar S M
SKSathish Kannan
Sathish Kannan
RTRavichandran A T
Ravichandran A T
Although Natural Fiber Reinforced Polymer Composites (NFRPCs) have been taken special place in the aerospace, automotive and construction sectors, owing to their sustainability and mechanical qualities, yet challenges continue in understanding their machining characteristics, especially when executing the slotting operation on the composite surfaces. In these footsteps current investigation is undertaken to study the effect of the fiber orientations on dynamic mechanical properties and milling behavior of flax fiber reinforced epoxy (FREp) composites. These composites are fabricated using hand layup process and designated as Type A (0/90°) and Type B (±45°) based on their reinforcement orientation. Dynamic mechanical experimental results showed that, Type A composite exhibited higher storage modulus property (E′). Though Type B composites suffer in storage modulus, exhibited higher loss modulus (E″) and damping properties than Type A composites due to their angled fiber structure which favors for increased internal friction and higher shear deformation with higher energy dissipation. Milling investigation was carried out as per the Taguchi’s design of experiment using L 9 Orthogonal arrays. Input factors namely, spindle speed (750, 1500 and 2250 rpm), feed rate (70, 90, and 110 mm/min) and depth of cut (1, 1.5, and 2 mm) were selected to study their effect of output responses such as cutting force, surface roughness and machinability index. Results revealed that, depth of cut is the main input factor affected the milling performance of the composite followed by cutting speed and feed rate. Moreover, Type A composite was easier to machine than Type B composites due to their fabric architecture. Milled surface of the FREp composites were subjected to field emission scanning electron microscopy (FESEM) to understand the damages endured during machining.