Guobiao Shi

Guobiao Shi

Auto-generated profile, based on publicly available information

Guobiao Shi

School of Mechanical Engineering, Beijing Institute of Technology, Beijing, China

Research Focus & Metrics

Academic Career Length

4Years (2023-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 December 2023 in IEEE Transactions on Intelligent Transportation Systems
Verified
Journal Article
Closed access
GSGuo-Biao Shi
Guo-Biao Shi
CGCong Guo
Cong Guo
Shuai WangShuai Wang
Shuai Wang
TLTing-Yang Liu
Ting-Yang Liu
In order to facilitate the application of steer-by-wire system in L3 and higher-level autonomous driving vehicle and overcome the shortcomings of the dual motor steer-by-wire system, such as difficult synchronization control, high mechanical accuracy requirements, and high cost, this paper proposes a steer-by-wire execution control scheme based on dual three-phase permanent magnet synchronous motor (PMSM). Firstly, the models of the dual three-phase PMSM, the steer-by-wire system and 2DOF vehicle are established. Then, an angle tracking strategy based on load torque observer and modified sliding mode control, and a redundancy reconstruction rule for the dual three-phase PMSM faults are designed. Finally, verification was conducted through simulation and hardware in loop (HIL)test bench. Simulation and experimental results show that the proposed angle tracking control strategy has excellent dynamic performance and can effectively reduce high-frequency chattering, while the proposed fault-tolerant control strategy can effectively reduce the fluctuations of motor speed and torque under faults. Therefore, the control strategies proposed in this paper not only can meet the high-performance requirements of lateral control of autonomous vehicles, but also can meet the high-safety requirements of steer-by-wire system in high-level autonomous vehicles.

21 February 2023 in Proceedings of the Institution of Mechanical Engineers, Part D: Journal of Automobile Engineering
Verified
Journal Article
Closed access
GSGuobiao Shi
Guobiao Shi
PQPengfei Qiao
Pengfei Qiao
DSDonggang Sang
Donggang Sang
Shuai WangShuai Wang
Shuai Wang
MSMinghao Song
Minghao Song
In order to meet the high safety requirement of high-level automatic steering mechanism for commercial vehicle, a kind of steer-by-wire (SBW) system with redundant motors is studied in this paper, and the structure principle and control strategy of the system are studied. Commercial vehicles have the characteristics of large steering resistance moment, which is accompanied by impact and vibration during steering, so the synchronous control of dual motors is the key and difficult problem. Based on the circulating ball steering gear for commercial vehicle, dual-motor synchronous control architecture is designed and the dual-motor global-fast-terminal-sliding-mode (nonsingular-GFTSM) synchronous control is formulated. Compared with the sliding-mode control, the simulation results show that the dual-motor actuator based on nonsingular-GFTSM can better realize the synchronous operation in angle, speed and torque. In addition, a real-time motor fault-diagnosis method based on sliding mode observer and a fault-tolerant control strategy based on smooth switching system are designed, which can achieve fast fault-isolation and smooth torque switching in case of actuator failure in dual-motor system. A Hardware-in-the-Loop (HIL) test bench is built to further verify the effectiveness of the synchronous and fault-tolerance control strategy for dual motors.

3 April 2024 in IEEE Transactions on Power Electronics
Verified
Journal Article
Closed access
QSQingle Sun
Qingle Sun
SSSuleiman M Sharkh
Suleiman M Sharkh
Zhifu Institute of WangZhifu Institute of Wang
Zhifu Institute of Wang
ZWZeshang Wang
Zeshang Wang
GSGuobiao Shi
Guobiao Shi
This article proposes novel space vector pulse width modulation strategies for multilevel converters to achieve two widely desired optimization objectives, common-mode voltage (CMV) elimination and switching frequency minimization (SFM). For CMV elimination, a new coordinate system that looks like the cropped version of the original abc frame is proposed, by which zero CMV can be ensured when the identified switching states are transformed from the new frame back into the original one. For SFM, a new approach is proposed to determine the optimal switching sequence, where a voltage reference point dwell mechanism is introduced such that the number of switching actions between adjacent switching periods is minimized by establishing its relationship with a unique variable, namely the number of level shifts. Furthermore, these two objectives can either be implemented independently or in combination to achieve SFM under the premise of CMV elimination, thus allowing the converter's redundancy to be fully exploited. Simulation and experimental results validate the proposed strategies.