Dmitry Shestakov

Dmitry Shestakov

Auto-generated profile, based on publicly available information

Dmitry Shestakov

School of Physics and Engineering, ITMO University, St. Petersburg, Russia

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 July 2023 in Optics & Laser Technology
Verified
Journal Article
Closed access
DSDmitry Shestakov
Dmitry Shestakov
EKEvgeniia Khairullina
Evgeniia Khairullina
ASAndrey Shishov
Andrey Shishov
SKSoslan Khubezhov
Soslan Khubezhov
SMSergey Makarov
Sergey Makarov
LLLev Logunov
Lev Logunov

1 December 2022 in Bulletin of the Russian Academy of Sciences: Physics
Verified
Journal Article
Closed access
PDF file
DSD. S. Shestakov
D. S. Shestakov
ASAndrey Shishov
Andrey Shishov
MMM. V. Mesh
M. V. Mesh
Ilya TumkinIlya Tumkin
Ilya Tumkin
SMSergey Makarov
Sergey Makarov
LLLev Logunov
Lev Logunov
For large scale production on light emitting diodes and solar cells it is necessary to create semitransparent electrodes with large area and low sheet resi

1 December 2024 in Bulletin of the Russian Academy of Sciences: Physics
Verified
Journal Article
Closed access
PDF file
AVAlexander Vasilevich Vavilov
Alexander Vasilevich Vavilov
Alexey ZakharovAlexey Zakharov
Alexey Zakharov
EKEvgeniia M. Khairullina
Evgeniia M. Khairullina
Ilya TumkinIlya Tumkin
Ilya Tumkin
DSD. Shestakov
D. Shestakov
LLLev Logunov
Lev Logunov
The task of local metallization of polymer substrates such as PDMS (polydimethylsiloxane) is a challenging and important task for the development of biocompatible flexible electronics. Here we present for the first time the possibility of using the Direct laser metallization (DLM) method for fabrication of copper conducting structures on PDMS. It has been shown that DLM method allows one to obtain conductive structures with low resistivity and a developed surface with minimal thermal impact on the substrate. By optimizing the scanning speed and laser power density, it was possible to minimize the thermal degradation of PDMS and ensure reliable metal adhesion. The DLM method opens up new opportunities for creating flexible electronics, providing precise and cost-effective deposition of copper conductors on flexible substrates.

7 October 2026 in EcoEnergy
Verified
Journal Article
Open access
PDF file
AFAleksandra Furasova
Aleksandra Furasova
ABAnna Botnar
Anna Botnar
VIVladimir Ivanov
Vladimir Ivanov
VBVadim Belyaev
Vadim Belyaev
Igor MargaryanIgor Margaryan
Igor Margaryan
SMSergey Makarov
Sergey Makarov
Polyelectrolytes represent a low‐cost and effective platform for tailoring charge extraction interfaces in inverted perovskite solar cells (PSCs). In this work, we introduce a protonated polyethyleneimine (PEI) layer (pH = 2) between the ITO electrode and the PTAA hole transport layer to increase the apparent work function of ITO by 0.066 eV and reduce contact resistance and the work‐function mismatch with PTAA from 0.170 to 0.104 eV. By incorporating low concentrations of PEI (0.3–1 mg/mL), we significantly increased the open‐circuit voltage up to 1.143 V and achieved a peak power conversion efficiency of 23.45%. The PEI‐modified devices maintain superior photovoltaic performance not only under standard AM 1.5 G illumination, but also at low sunlight intensities (30 and 50 mW/cm 2 ) and under indoor illumination conditions. These results highlight the potential of protonated polyelectrolyte interlayers for developing efficient and versatile PSCs suitable for both outdoor and ambient‐light applications.

1 December 2025 in Bulletin of the Russian Academy of Sciences: Physics
Verified
Journal Article
Closed access
PDF file
LLLev Logunov
Lev Logunov
EAE. Afanaseva
E. Afanaseva
APA. Pilipchuk
A. Pilipchuk
VKV. Kostyukova
V. Kostyukova
DSD. Shestakov
D. Shestakov
EDE. Danilovskiy
E. Danilovskiy
We presented a novel, maskless approach for fabricating copper electrodes on flexible polyimide substrates using direct laser metallization (DLM) from deep eutectic solvents (DES). The DLM process utilizes localized thermochemical reactions driven by a picosecond pulsed laser to convert DES precursors into conductive copper structures with precise patterning. Key parameters such as laser power density, scanning speed, and DES layer thickness were optimized to achieve uniform copper lines with excellent electrical conductivity and mechanical flexibility. The fabricated electrodes demonstrated remarkable stability under bending tests, showing less than 5% variation in resistance, which confirms their suitability for flexible pressure and strain sensor applications in wearable electronics and human–machine interfaces. This is the first demonstration of copper structures produced on polyimide via DES-based DLM with proven functional performance, highlighting its potential as a scalable, cost-effective method for next-generation flexible electronic device manufacturing.