Emiel van de Ven

Emiel van de Ven

Auto-generated profile, based on publicly available information

Emiel van de Ven

Faculty of Mechanical, Maritime and Materials Engineering, Delft University of Technology, Delft, The Netherlands

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 January 2018 in Structural and Multidisciplinary Optimization
Verified
Journal Article
Open access
PDF file
EVEmiel van de Ven
Emiel van de Ven
RMRobert Maas
Robert Maas
CACan Ayas
Can Ayas
MLMatthijs Langelaar
Matthijs Langelaar
FKFred van Keulen
Fred van Keulen
Additive manufacturing enables the nearly uncompromised production of optimized topologies. However, due to the overhang limitation, some designs require a large number of supporting structures to enable manufacturing. Because these supports are costly to build and difficult to remove, it is desirable to find alternative designs that do not require support. In this work, a filter is presented that suppresses non-manufacturable regions within the topology optimization loop, resulting in designs that can be manufactured without the need for supports. The filter is based on front propagation, can be evaluated efficiently, and adjoint sensitivities are calculated with almost no additional computational cost. The filter can be applied also to unstructured meshes and the permissible degree of overhang can be freely chosen. The method is demonstrated on several compliance minimization problems in which its computational efficiency and flexibility are shown. The current applications are in 2D, and the proposed method is readily extensible to 3D.

1 December 2021 in Computer Methods in Applied Mechanics and Engineering
Verified
Journal Article
Open access
GMGrzegorz Misiun
Grzegorz Misiun
EVEmiel van de Ven
Emiel van de Ven
MLMatthijs Langelaar
Matthijs Langelaar
HGHubert Geijselaers
Hubert Geijselaers
FKFred van Keulen
Fred van Keulen
CACan Ayas
Can Ayas

1 September 2020 in Computer Methods in Applied Mechanics and Engineering
Verified
Journal Article
Open access
EVEmiel van de Ven
Emiel van de Ven
RMRobert Maas
Robert Maas
CACan Ayas
Can Ayas
MLMatthijs Langelaar
Matthijs Langelaar
FKFred van Keulen
Fred van Keulen

2 June 2021 in Structural and Multidisciplinary Optimization
Verified
Journal Article
Open access
PDF file
EVEmiel van de Ven
Emiel van de Ven
RMRobert Maas
Robert Maas
CACan Ayas
Can Ayas
MLMatthijs Langelaar
Matthijs Langelaar
FKFred van Keulen
Fred van Keulen
Although additive manufacturing (AM) allows for a large design freedom, there are some manufacturing limitations that have to be taken into consideration. One of the most restricting design rules is the minimum allowable overhang angle. To make topology optimization suitable for AM, several algorithms have been published to enforce a minimum overhang angle. In this work, the layer-by-layer overhang filter proposed by Langelaar (Struct Multidiscip Optim 55(3):871–883, 2017), and the continuous, front propagation-based, overhang filter proposed by van de Ven et al. (Struct Multidiscipl Optim 57(5):2075–2091, 2018) are compared in detail. First, it is shown that the discrete layer-by-layer filter can be formulated in a continuous setting using front propagation. Then, a comparison is made in which the advantages and disadvantages of both methods are highlighted. Finally, the continuous overhang filter is improved by incorporating complementary aspects of the layer-by-layer filter: continuation of the overhang filter and a parameter that had to be user-defined are no longer required. An implementation of the improved continuous overhang filter is provided.

21 December 2020 in International Journal for Numerical Methods in Engineering
Verified
Journal Article
Open access
PDF file
EVEmiel van de Ven
Emiel van de Ven
CACan Ayas
Can Ayas
MLMatthijs Langelaar
Matthijs Langelaar
RMRobert Maas
Robert Maas
FKFred van Keulen
Fred van Keulen
Additive manufacturing (AM) and topology optimization (TO) have a synergetic relation, as AM can produce complex TO designs, and TO provides high‐performance parts that utilize the form freedom provided by AM. Recently, TO has been tailored more toward AM with the inclusion of the minimum allowable overhang angle as a design constraint: resulting designs can be built without any support structures. This work is an extension thereof, by allowing support structures only if they are accessible, such that they can be removed after manufacturing. This is achieved by applying a conventional overhang filter twice, combined with basic operations such as geometry inversion, union, and intersection. The result is an accessibility‐aware overhang filter that can be incorporated in TO. Compared with conventional overhang filtered designs, the accessibility filter results in increased part performance and better convergence behavior. Furthermore, a modular filter structure is presented to easily construct the accessibility filter, and its effectiveness is demonstrated on several numerical cases.