In the last few decades, piezoresponse force microscopy (PFM) has been a valuable tool to analyze ferroelectric materials at nanoscale. Domain switching and phase-hysteresis loops acquired by PFM had been taken as a proof of ferroelectricity; however, these two characteristics have been observed in non-ferroelectric materials, generating uncertainty of the characterizations carried out by PFM. To resolve this problem, strategies have been developed but they are difficult to implement or still fail depending on the measurement conditions. In this work, we provide a simple method to effectively differentiate ferroelectric from non-ferroelectric signals in PFM analyses. It is based on the comparison of the phases of the PFM signals obtained at the first and the second harmonics of the contact resonant frequency of the Vac applied between the tip and the bottom electrode. To illustrate the effectiveness and simplicity of the method, analyses were conducted on a ferroelectric PZT film, a non-ferroelectric glass and SrTiO3 sample, and a KNN ceramic with ferroelectric and non-ferroelectric zones.
Single-frequency piezoresponse force microscopy (PFM) images of a BiFeO3/DyScO3(110) thin film, obtained with long (kc = 0.82 N/m) and short (kc = 7.64 N/m) cantilevers, were analyzed as a function of the applied voltage frequency. For long cantilevers, the electrostatic and electrostrictive contributions were identified. These contributions were reduced with a frequency near the second mode of the contact resonance; while for short cantilevers, the first mode was necessary. A method for domain structure analyses, to discriminate a ferroelectric behavior from a non-ferroelectric, through the optimization of PFM images, is also described. The analysis can be extended to cantilevers with different spring constants and ferroelectric materials.
This study presents the synthesis and characterization of TiN hard coatings as a candidate reference material for surface metrology in chemistry. TiN coatings were grown on a silicon wafer with (111) orientation using dc reactive magnetron sputtering. X-ray diffraction confirms that the diffraction phase of TiN coatings is polycrystalline, electron microscopy demonstrates that the TiN coatings presents pyramidal-shaped grains ranging from sub-micrometer to nano-size scale and with an average thickness of 666 nm. According to micro Raman results, the presence of LO phonon modes confirms that the TiN coatings are crystalline in nature and no impurities are detected. The mechanical properties at the nanoscale are evaluated using resonance tracking acoustic force atomic microscopy. The chemical composition of the TiN reveals a close 1:1 atomic ratio. The ANOVA is used to evaluate the homogeneity of the TiN via a homogeneity test according to the ISO Guide 35:2017, while, regarding the chemical composition of the Ti, the Fisher’s test demonstrates that the batch can be considered as homogeneous.
In this work, a high-resolution atomic force acoustic microscopy imaging technique is developed in order to obtain the local indentation modulus at the nanoscale level. The technique uses a model that gives a qualitative relationship between a set of contact resonance frequencies and the indentation modulus. It is based on white-noise excitation of the tip–sample interaction and uses system theory for the extraction of the resonance modes. During conventional scanning, for each pixel, the tip–sample interaction is excited with a white-noise signal. Then, a fast Fourier transform is applied to the deflection signal that comes from the photodiodes of the atomic force microscopy (AFM) equipment. This approach allows for the measurement of several vibrational modes in a single step with high frequency resolution, with less computational cost and at a faster speed than other similar techniques. This technique is referred to as stochastic atomic force acoustic microscopy (S-AFAM), and the frequency shifts of the free resonance frequencies of an AFM cantilever are used to determine the mechanical properties of a material. S-AFAM is implemented and compared with a conventional technique (resonance tracking-atomic force acoustic microscopy, RT-AFAM). A sample of a graphite film on a glass substrate is analyzed. S-AFAM can be implemented in any AFM system due to its reduced instrumentation requirements compared to conventional techniques.
This work documents the study of samples of CNx/MoS2 multilayer coatings, deposited by magnetron sputtering technique, using 10% and 16% of N2 concentration in the Ar/N2 gas mixture to obtain two sample sets with different nitrogen concentrations in the CNx layers. The samples were grown on Si (100) and AISI 304 steel substrates to carry out different characterizations. The microstructure of the samples was investigated by scanning electron microscopy (SEM), atomic force microscopy (AFM) and x-ray diffraction (XRD). The chemical structure and vibrational modes present in the multilayer coatings were evaluated using x-ray photoelectron spectroscopy (XPS), and Raman spectroscopy, respectively. The analysis revealed that the CNx layers are amorphous, while the MoS2 layers show a polycrystalline structure with basal planes perpendicular to the substrate surface. Finally, the mechanical properties were evaluated by nanoindentation and pin on disk tests, respectively. The results revealed that the concentration of N in the CNx layer is fundamental in determining the mechanical properties. In the test carried out in a humid environment, the samples with the lowest concentration of N in the CNx layers present lower values in the coefficient of friction.