1 January 2017 in Journal of Advanced Transportation
Dedicated short-range communication (DSRC) and 4G-LTE are two widely used candidate schemes for Connected Vehicle (CV) applications. It is thus of great necessity to compare these two most viable communication standards and clarify which one can meet the requirements of most V2X scenarios with respect to road safety, traffic efficiency, and infotainment. To the best of our knowledge, almost all the existing studies on comparing the feasibility of DRSC or LTE in V2X applications use software-based simulations, which may not represent realistic constraints. In this paper, a Connected Vehicle test-bed is established, which integrates the DSRC roadside units, 4G-LTE cellular communication stations, and vehicular on-board terminals. Three Connected Vehicle application scenarios are set as Collision Avoidance, Traffic Text Message Broadcast, and Multimedia File Download, respectively. A software tool is developed to record GPS positions/velocities of the test vehicles and record certain wireless communication performance indicators. The experiments have been carried out under different conditions. According to our results, 4G-LTE is more preferred for the nonsafety applications, such as traffic information transmission, file download, or Internet accessing, which does not necessarily require the high-speed real-time communication, while for the safety applications, such as Collision Avoidance or electronic traffic sign, DSRC outperforms the 4G-LTE.
1 January 2004 in Transportation Research Record: Journal of the Transportation Research Board
A methodology is presented for estimating and predicting the total annual traffic congestion attributable to recurrent and nonrecurrent congestion. The methodology is applicable to freeways, conventional highways, and urban streets. The methodology is sensitive to improvements in facility surveillance and freeway service patrol strategies. Recurrent congestion is estimated by using Highway Capacity Manual speed-flow curves and data on facility demands, free-flow speeds, and capacities. Nonrecurrent congestion is estimated in terms of annual vehicle hours of delay caused by weather, work zones, incidents, and so forth. The methodology employs incident probability trees, incident duration (sensitive to surveillance and response times), and estimates of remaining capacity during incidents to estimate incident delay. Weather-and work-zone-related delays are estimated on the basis of frequency of occurrence and estimates of capacity reductions during periods of bad weather and work-zone activity. The methodology has been implemented in a spreadsheet.
1 February 2016 in Journal of Transportation Engineering
Ramp metering has been proven as an effective freeway-management strategy; however, one of the critical challenges in design and operation of ramp metering is the lack of up-to-date design guidance for acceleration lanes. This paper aims to investigate the actual acceleration characteristics for metered on-ramps with various geometric features and also figure out speed profiles to guide the design of acceleration-lane length. A piecewise-constant acceleration model, which assumes vehicles making uniformly accelerated motion within each short space or time interval, was employed to model vehicle acceleration characteristics. The approach of using distance versus speed profiles for acceleration-length design was also introduced. Results show that acceleration rate at metered on-ramps is not constant; vehicles usually accelerate at a higher acceleration rate when speed is lower and vice versa. It was observed that taper ramps usually produce higher acceleration rates than ramps with an auxiliary lane...
16 October 2017 in Transportmetrica A: Transport Science
This paper compares queue lengths at the two different on-ramp configurations: arterial-to-freeway ramp and freeway-to-freeway connector. Mesoscopic queue length simulation models are developed based on the input-output method. The input-output method aims to model the traffic flow arrival profile; then, the mesoscopic simulation model generates random traffic volume to simulate the stochasticity of traffic flow. The simulation models are validated using field-collected data. Simulation results indicated that the traffic flow arrival pattern has significant impacts on ramp queue length; vehicle platoons released from the upstream signalized intersection tend to exacerbate ramp queue length. At metered ramps, the required queue storage length is found to be 5.7% of demand when demand is less than 500 vehicles per hour per lane (vphpl), or 3.9% when demand is greater than 500 vehicles per hour per lane (vphpl). In comparison, at metered connectors, the percent numbers are 4.7 and 2.1%, respectively.
1 October 2005 in Journal of Intelligent Transportation Systems
Loop detectors have been widely used to estimate travel time delay. One implicit assumption about the estimation is that traffic flow is stationary. Based on this assumption, the point data collected by loop detectors at different locations could be interpolated or extrapolated to estimate travel time delay for segments between adjacent loop detectors. This assumption is not quite valid when vehicle speeds fluctuate spatially and temporally. It is desirable to examine and understand the accuracy level of such travel time delay estimation methodology in real-world situations. The purpose of this article is to present an empirical analysis to explicitly illustrate the accuracy level of travel time delay estimated using loop detectors. Travel time delay obtained from eight freeway segments under various combinations of reference speeds, data aggregation intervals, and loop detector spacings are studied and compared with true delay determined using vehicle trajectory information. For all of the eight freeway segments evaluated, it was found that the mean absolute percentage errors of estimated delay are consistently less than 7%, when delay is defined using a reference speed higher than 60 mph (96 kmph). Higher mean absolute percentage errors were observed for lower reference speeds, longer detector spacings and turbulent traffic situations, such as traffic incidents. Adopting higher reference speed, say 60 mph (96 kmph), longer data aggregation interval, say 300-second, and shorter loop detector spacing, say 1,000 ft (305 m), helps produce lower mean absolute percentage error in loop detector-estimated travel time delay.
1 January 2016 in Transportation Research Record: Journal of the Transportation Research Board
AASHTO’s A Policy on Geometric Design of Highways and Streets (Green Book) is currently used by most state departments of transportation in the United States in determining the design length of acceleration lanes of metered on-ramps; however, the recommended acceleration lengths have not been updated for several decades. This study aimed to develop a method for determining acceleration lengths at metered on-ramps. Vehicle location versus time information was collected via parallel cameras at seven metered on-ramps in California; then, a piecewise constant acceleration model was proposed to calculate the spot speeds of individual samples at predetermined locations. The percentile distance-versus-speed profiles at each ramp were built, and regression models were generated to predict the required acceleration length at a given merge speed. The 85th percentile data were recommended as the minimum acceleration length to accommodate most drivers in accelerating to a safe merging speed. The new recommendation was compared with the existing guidance in the Green Book. On the basis of 1,658 individual samples, it was found that the recommended acceleration lengths were shorter than the Green Book guidelines by 10% to 35%. Also, results showed that acceleration lengths for tractor trailer trucks were approximately 60% greater than the Green Book guidelines.