23 August 2018 in Journal of Fluid Mechanics
High-fidelity experiments of Richtmyer–Meshkov instability on a single-mode air/ $\text{SF}_{6}$ interface are carried out at weak shock conditions. The soap-film technique is extended to create single-mode gaseous interfaces which are free of small-wavelength perturbations, diffusion layers and three-dimensionality. The interfacial morphologies captured show that the instability evolution evidently involves the smallest experimental uncertainty among all existing results. The performances of the impulsive model and other nonlinear models are thoroughly examined through temporal variations of the perturbation amplitude. The individual growth of bubbles or spikes demonstrates that all nonlinear models can provide a reliable forecast of bubble development, but only the model of Zhang & Guo (J. Fluid Mech., vol. 786, 2016, pp. 47–61) can reasonably predict spike development. The distinct images of the interface morphology obtained also provide a rare opportunity to extract interface contours such that a spectral analysis of the interfacial contours can be performed, which realizes the first direct validation of the high-order nonlinear models of Zhang & Sohn (Phys. Fluids, vol. 9, 1997, pp. 1106–1124) and Vandenboomgaerde et al. (Phys. Fluids, vol. 14 (3), 2002, pp. 1111–1122) in terms of the fundamental mode and high-order harmonics. It is found that both models show a very good and almost identical accuracy in predicting the first two modes. However, the model of Zhang & Sohn (1997) becomes much more accurate in modelling the third-order harmonics due to the fewer simplifications used.
1 October 2018 in Physics of Fluids
Interactions of a planar shock wave with two-dimensional (2D), three-dimensional (3D) concave, and 3D convex SF6 cylindrical bubbles surrounded by air are studied both experimentally and numerically. The effects of initial interface curvature on the bubble deformation and wave propagation are highlighted. The cylindrical bubbles are generated by a wire-restriction method based on the soap-film technique, and their shapes are well controlled by adjusting the pressure difference across the interface. The high-speed schlieren results demonstrate that the evolving interfaces develop more symmetrically than previous studies as they are free of holder and fewer disturbance waves are generated. Typical evolution processes of the 2D bubble such as the jet formation and vortex pair formation are clearly captured. Compared with the 2D case, the oppositely (identically) signed principal curvatures of the concave (convex) boundary produce more complicated high pressure fields and 3D additional baroclinic vorticity. For 3D cases, the numerical results show that the wave patterns in the symmetry or boundary slice are distinct from the 2D case owing to the 3D movement of the generated waves, and the jet structure presents an evident three dimensionality. In particular, for the concave bubble, a certain slice between the boundary and symmetry slices presents the fastest-developing jet, while for the convex case the fastest jet emerges at the boundary slice. The upstream interface along the symmetry slice of the concave (convex) bubble moves faster (slower) than that of the 2D case, which is reasonably predicted by a 3D theoretical model.
13 June 2019 in Journal of Fluid Mechanics
Experiments on Richtmyer–Meshkov instability of quasi-single-mode interfaces are performed. Four quasi-single-mode air/ $\text{SF}_{6}$ interfaces with different deviations from the single-mode one are generated by the soap film technique to evaluate the effects of high-order modes on amplitude growth in the linear and weakly nonlinear stages. For each case, two different initial amplitudes are considered to highlight the high-amplitude effect. For the single-mode and saw-tooth interfaces with high initial amplitude, a cavity is observed at the spike head, providing experimental evidence for the previous numerical results for the first time. For the quasi-single-mode interfaces, the fundamental mode is the dominant one such that it determines the amplitude linear growth, and subsequently the impulsive theory gives a reasonable prediction of the experiments by introducing a reduction factor. The discrepancy in linear growth rates between the experiment and the prediction is amplified as the quasi-single-mode interface deviates more severely from the single-mode one. In the weakly nonlinear stage, the nonlinear model valid for a single-mode interface with small amplitude loses efficacy, which indicates that the effects of high-order modes on amplitude growth must be considered. For the saw-tooth interface with small amplitude, the amplitudes of the first three harmonics are extracted from the experiment and compared with the previous theory. The comparison proves that each initial mode develops independently in the linear and weakly nonlinear stages. A nonlinear model proposed by Zhang & Guo (J. Fluid Mech., vol. 786, 2016, pp. 47–61) is then modified by considering the effects of high-order modes. The modified model is proved to be valid in the weakly nonlinear stage even for the cases with high initial amplitude. More high-order modes are needed to match the experiment for the interfaces with a more severe deviation from the single-mode one.
8 June 2021 in Journal of Fluid Mechanics
Investigation on the shock-induced finite-thickness fluid-layer evolution is very desirable but remains a challenge because it not only involves both the Richtmyer–Meshkov instability (RMI) and the Rayleigh–Taylor instability (RTI), but also strongly depends on the waves reverberated inside the layer. We experimentally and theoretically examined the evolution of a shocked gas layers with diverse layer thicknesses and amplitude combinations are created to explore the interfacial instabilities of the layer. When the initial fluid layer is thin, the two interfaces of the layer coalesce at a late time. The present study is the first to report that except for the RMI induced by a shock wave on the two interfaces, the rarefaction waves (RW) inside the fluid layer induce the additional RTI and decompression effect on the first interface, and the compression waves (CW) inside the fluid layer cause the additional Rayleigh–Taylor stabilisation (RTS) and compression effect on the second interface. A general one-dimensional theory is established to describe the motions of the two interfaces. Linear and nonlinear models are successfully established by considering the interface-coupling effect on the RMI and the additional interfacial instabilities induced by these waves inside the heavy fluid layer. The established models predict well the perturbation growths on the two interfaces at all regimes.
6 January 2020 in Journal of Fluid Mechanics
The interaction of a shock wave and a water droplet embedded with a vapour cavity is experimentally investigated in a shock tube for the first time. The vapour cavity inside the droplet is generated by decreasing the surrounding pressure to the saturation pressure, and an equilibrium between the liquid phase and the gas phase is obtained inside the droplet. Direct high-speed photography is adopted to capture the evolution of both the droplet and the vapour cavity. The formation of a transverse jet inside the droplet during the cavity-collapse stage is clearly observed. Soon afterwards, at the downstream pole of the droplet, a water jet penetrating into the surrounding air is observed during the cavity-expansion stage. The evolution of the droplet is strongly influenced by the evolution of the vapour cavity. The phase change process plays an important role in vapour cavity evolution. The effects of the relative size and eccentricity of the cavity on the movement and deformation of the droplet are presented quantitatively.
8 January 2020 in Journal of Fluid Mechanics
Richtmyer–Meshkov instability of the SF6 gas layer surrounded by air is experimentally investigated. Using the soap film technique, five kinds of gas layer with two sharp interfaces are generated such that the development of each individual interface is highlighted. The flow patterns are determined by the amplitudes and phases of two corrugated interfaces. For a layer with both interfaces planar, the interface velocity shows that the reflected rarefaction waves from the second interface accelerate the first interface motion. For a layer with the second interface corrugated but the first interface planar, the reflected rarefaction waves make the first interface develop with the same phase as the second interface. For a layer with the first interface corrugated but the second interface planar, the rippled shock seeded from the first interface makes the second interface develop with the same phase as the first interface and the layer evolves into an ‘upstream mushroom’ shape. For two interfaces corrugated with opposite (the same) phase but a larger amplitude for the first interface, the layer evolves into ‘sinuous’ shape (‘bow and arrow’ shape, which has never been observed previously). For the interface amplitude growth in the linear stage, the waves’ effects are considered in the model to give a better prediction. In the nonlinear stage, the effect of the rarefaction waves on the first interface evolution is quantitatively evaluated, and the nonlinear growth is well predicted. It is the first time in experiments to quantify the interfacial instability induced by the rarefaction waves inside the heavy gas layer.