16 October 2017 in Advanced Science
Tin‐based chalcogenide semiconductors, though attractive materials for photovoltaics, have to date exhibited poor performance and stability for photoelectrochemical applications. Here, a novel strategy is reported to improve performance and stability of tin monosulfide (SnS) nanoplatelet thin films for H2 production in acidic media without any use of sacrificial reagent. P‐type SnS nanoplatelet films are coated with the n‐CdS buffer layer and the TiO2 passivation layer to form type II heterojunction photocathodes. These photocathodes with subsequent deposition of Pt nanoparticles generate a photovoltage of 300 mV and a photocurrent density of 2.4 mA cm−2 at 0 V versus reversible hydrogen electrode (RHE) for water splitting under simulated visible‐light illumination (λ > 500 nm, Pin = 80 mW cm−2). The incident photon‐to‐current efficiency at 0 V versus RHE for H2 production reach a maximum of 12.7% at 575 nm with internal quantum efficiency of 13.8%. The faradaic efficiency for hydrogen evolution remains close to unity after 6000 s of illumination, confirming the robustness of the heterojunction for solar H2 production.
6 November 2018 in Frontiers in Chemistry
Minimizing Pt loading is essential for designing cost-effective water electrolyzers and fuel cell systems. Recently, three-dimensional macroporous open-pore electroactive supports have been widely regarded as promising architectures to lower loading amounts of Pt because of its large surface area, easy electrolyte access to Pt sites, and superior gas diffusion properties to accelerate diffusion of H2 bubbles from the Pt surface. However, studies to date have mainly focused on Pt loading on Ni-based 3D open pore supports which are prone to corrosion in highly acidic and alkaline conditions. Here, we investigate electrodeposition of Pt nanoparticles in low-loading amounts on commercially available, inexpensive, 3D carbon foam (CF) support and benchmark their activity and stability for electrolytic hydrogen production. We first elucidate the effect of deposition potential on the Pt nanoparticle size, density and subsequently its coverage on 3D CF. Analysis of the Pt deposit using scanning electron microscopy images reveal that for a given deposition charge density, the particle density increases (with cubic power) and particle size decreases (linearly) with deposition overpotential. A deposition potential of −0.4 V vs. standard calomel electrode (SCE) provided the highest Pt nanoparticle coverage on 3D CF surface. Different loading amounts of Pt (0.0075–0.1 mgPt/cm2) was then deposited on CF at −0.4 V vs. SCE and subsequently studied for its hydrogen evolution reaction (HER) activity in acidic 1M H2SO4 electrolyte. The Pt/CF catalyst with loading amounts as low as 0.06 mgPt/cm2 (10-fold lower than state-of-the-art commercial electrodes) demonstrated a mass activity of 2.6 ampere per milligram Pt at 200 mV overpotential, nearly 6-fold greater than the commercial Pt/C catalyst tested under similar conditions. The 3D architectured electrode also demonstrated excellent stability, showing <7% loss in activity after 60 h of constant current water electrolysis at 100 mA/cm2.
17 June 2021 in Chemical Communications
Surface wettability plays an important role in heterogeneous electrocatalysis. Here we report a facile laser ablation strategy to directly modify the wettability of the silver catalyst surface and investigate its effect on oxygen reduction reaction (ORR). A broad range tuning of 2e−/4e− ORR pathways was achieved, with hydrophilic silver surfaces (contact angle (θw) 31.1° ± 0.6°) showing high activity and selectivity towards 4e− reduction of oxygen to water.
10 October 2016 in Chemical Communications
A plasmonic liquid junction photovoltaic cell with greatly improved power conversion efficiency is described. When illuminated with simulated sunlight, the device (Au–TiO2/V3+(0.018 M), V2+(0.182 M)/Pt) reproducibly and sustainably produces an VOC of 0.50 V and a JSC of 0.5 mA cm−2, corresponding to a power conversion efficiency of 0.095%.
4 May 2023 in Environmental Science: Advances
ABAshley Hesterberg Butzlaff
Ashley Hesterberg Butzlaff
+1
Electrochemical (EC) and photoelectrochemical (PEC) water treatment systems are gaining popularity, necessitating new electrode materials that offer reliable performance across diverse application platforms. For applications specifically targeting dilute chemical pollutants (i.e., parts-per-million concentrations or less), beneficial electrode properties include high surface area to overcome kinetic overpotential losses, low electrode areal electrical resistance, and high water permeability with sufficient mechanical strength for use in electroactive membrane-based treatment systems. Here, we used electrospinning to fabricate (photo)electrodes from carbon nanofibers (CNFs) containing titanium dioxide (TiO2) nanoparticles. Optimal CNF/TiO2 composites were electrochemically and photoelectrochemically active with a surface area of ~50 m2 g-1 and electrode areal resistance of 2.66 Ω-cm2, values comparable to commercial carbon-based electrode materials (e.g., Kynol Activated Carbon Cloth). Transformation experiments with carbamazepine (CBZ), a recalcitrant organic contaminant, suggest CNF/TiO2 electrodes initially sorb CBZ prior to electrooxidation at positive applied potentials. Complete CBZ transformation was observed in both EC (dark) and PEC (UV light; 280 mW cm-2) systems over 90 minutes, with PEC systems exhibiting 1.5-fold higher transformation rates (kobs ~ 0.18 min-1) at +1.00 V (vs. Ag/AgCl). Composite electrodes also exhibited stability across repeated use, yielding consistent current densities over five experimental cycles (120 min each) of CBZ transformation (0.25 ± 0.03 mA cm-2). Because of their high surface area, electrical conductivity, photoactivity, and electrochemical stability, these electrospun CNF/TiO2 composites represent promising (photo)electrode alternatives for diverse EC and PEC applications.
6 October 2025 in The Journal of Physical Chemistry C