Zakir Çaldıran

Zakir Çaldıran

Auto-generated profile, based on publicly available information

Zakir Çaldıran

Ardahan Üniversitesi

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications

1 September 2021 in Sensors and Actuators A: Physical
Verified
Journal Article
Closed access
ZÇZakir Çaldıran
Zakir Çaldıran
LTLütfi Bilal Taşyürek
Lütfi Bilal Taşyürek

26 May 2025 in Journal of Materials Science: Materials in Electronics
Verified
Journal Article
Open access
PDF file
ZÇZakir Çaldıran
Zakir Çaldıran
This study explores the device properties of vanadium pentoxide (V2O5) thin films in the Cr/V2O5/p-Si/Al junction diode structure. The experimental setup utilized p-type silicon (p-Si) wafers with a resistivity of 1–10 Ω/cm and a thickness of 400 µm, chemically cleaned using the RCA1 and RCA2 protocols. Aluminum (Al) was deposited on one surface of the wafer as a back contact and annealed at 580 °C to establish ohmic behavior. A 10 nm layer of V2O5 was thermally deposited on the opposite surface and followed by a 100 nm top contact of Cr was deposited by DC sputtering. For comparison, a Cr/p-Si/Al reference device was fabricated under identical conditions, excluding the V2O5 layer. Electrical measurements, including I–V and diode parameter analyses, were performed at room temperature using TE theory, Cheung, and Norde functions. Ideality factor (IF) and barrier height (BH) for the reference diode from the TE method were determined to be 2.03 and 0.58 eV, while the 8 V2O5-based devices exhibited IF values ranging from 1.89 to 1.96 and BH values between 0.68 and 0.74 eV. The best performing device, designated device 5, achieved an IF value of 1.90 and a BH value of 0.74 eV. In addition, the photodiode properties of this device were analyzed under a solar simulator. These results indicate that the incorporation of the V2O5 interface layer improves the barrier properties of the diode and has potential for advanced rectification and photovoltaic applications. The presence of the series resistance (SR) and interface layer in the device and the inhomogeneity of the BH are also considered as factors contributing to that increase in IF. C–V characterization, another critical technique for understanding the electrical parameters of Schottky-type devices, was used to calculate important parameters such as BH and carrier concentration for the best performing device. Furthermore, G/ω–V and Z–V measurements at different frequencies were analyzed to better understand the electrical properties and surface/interface states of the device with the V2O5 interface.


4 March 2021 in Materials Today: Proceedings
Verified
Journal Article
Closed access
YNY. Nuhoglu
Y. Nuhoglu
ZCZ. Caldiran
Z. Caldiran
HKH. Kacus
H. Kacus
BCB. Cakmak
B. Cakmak

23 April 2026 in Journal of Studies in Advanced Technologies
Verified
Journal Article
Closed access
ZÇZakir Çaldıran
Zakir Çaldıran
YÖYildiz Özdemir
Yildiz Özdemir
YSYılmaz SAHİN
Yılmaz SAHİN
In this study, the effects of high-energy X-ray irradiation on the electrical characteristics of Au/LiF/p-Si/Al barrier diodes were investigated. The device structure was obtained by inserting a thin lithium fluoride (LiF) interfacial layer between gold (Au) and p-type silicon (p-Si) using the thermal evaporation method. The current–voltage (I–V) characteristics of the fabricated diodes were measured under dark conditions at room temperature (300 K). The samples were exposed to X-ray radiation doses of 0 Gy (before irradiation), 25, 50, and 75 Gy, and the variations in the main diode parameters, namely the ideality factor (n), barrier height (Φb), and series resistance (Rs), were analyzed. The electrical parameters were calculated using the thermionic emission (TE) theory, and a detailed analysis was also performed using the Cheung and Norde methods. For the Au/LiF/p-Si/Al device, the ideality factor and barrier height using TE were calculated as 1.22 and 0.64 eV, respectively, before irradiation. At 25 Gy, the ideality factor and barrier height of the device were found to be 1.29 and 0.68 eV, respectively, while at 75 Gy, these values changed to 1.76 and 0.82 eV, respectively. Similar behavior has been observed in calculations using other methods. The obtained results indicated that irradiation significantly affects the diode behavior. Deviations from ideal behavior were observed with increasing radiation dose, which were attributed to radiation-induced defects and interface states.