The light-induced fluorescence (LIF) represents an important tool for the continuous improvement and further development of combustion engine systems regarding efficiency increase. In this work, the interactions between light-emitting diode (LED) and laser diode light radiation, engine oil/fuel and three fluorescence tracers are investigated on an application-related investigation system for the design of qualitative LIF experiments. Thereby two efficient light sources for engine combustion chamber lighting are presented. For different engine oil/fuel tracer combinations, the fluorescence is examined in its intensity and its spectrum depending on the temperature, concentration and temperature history. With oil temperature variations of up to 150 °C, changes in the fluorescence spectrum and fluorescence intensities that decrease by up to 80% are evident. For specific tracer oil/fuel mixtures, concentration-dependent maximum intensities and different temperature history behaviors can be revealed. The results shown support the design of spectral engine examination setups and give tracer dosage recommendations. Additionally, an engine LIF setup for in-cylinder tracking of engine operating media is presented.
25 October 1999 in SAE International Journal of Advances and Current Practices in Mobility
In this paper optical investigations of a gasoline direct injection engine with narrow spacing arrangement of spark plug and injector are presented. For the combustion analysis spectroscopy techniques based on the fiber technique are used. With this measurement technique information about soot formation and temperature progression in the combustion chamber is obtained. Furthermore a validation of numerical simulation of the stratified combustion with data obtained experimentally, is performed and discussed.
In this work the surface structure of combustion chamber deposits (CCD) on the piston top and the cylinder head is described. By means of an optical profiler the roughness and maximum structure heights are measured. Scanning electron microscope images allow evaluating the structure of the deposits on the surface. The oil influence on CCD formation is assessed using energy-dispersive X-ray spectroscopy to quantify typical oil additives such as Mg, Ca or Zn in the deposits. By means of direct numerical simulation the influence of the CCD structure on near wall flow and hence on convective heat transfer is assessed. With fast surface thermocouples the temperature fluctuation on the cylinder head is measured. Applying two different model approaches—Hopwood and two-layer-model—the CCD layer thickness is calculated. By correlating the results with layer thickness measurements by the above mentioned optical profiler the values of the thermal conductivity for the CCD layers are calculated.
The root cause of the initial low-speed pre-ignition (LSPI) is not yet clarified. The literature data suggest that a two-phase phenomenon is most likely triggering the unpredictable premature ignitions in highly boosted spark-ignition engines. However, there are different hypotheses regarding the actual initiator, whether it is a detached liquid oil-fuel droplet or a solid-like particle from deposits. Therefore, the present work investigates the possibility of oil droplet-induced pre-ignitions using a modern downsized engine with minimally invasive endoscopic optical accessibility incorporating in-cylinder lubrication oil detection via light-induced fluorescence. This setup enables the differentiation between liquid and solid particles. Furthermore, the potential of hot solid particles to initiate an ignition under engine-relevant conditions is analyzed numerically. To do so, the particle is generalized as a hot surface transferring heat to the reactive ambient gas phase. The gas-phase reactivity is represented as a TRF/air mixture based on RON/MON specifications of the investigated fuel. The chemical processes are predicted using a semi-detailed reaction mechanism, including 137 species and 633 reactions in a 2D CFD simulation framework. In the optical experiments, no evidence of a liquid oil droplet-induced pre-ignition could be found. Nevertheless, all observed pre-ignitions had a history of flying light-emitting objects. There are strong hints towards solid-like deposit LSPI initiation. The application of the numerical methodology to mean in-cylinder conditions of an LSPI prone engine operation point reveals that particles below 1000 K are not able to initiate a pre-ignition. A sensitivity analysis of the thermodynamic boundary conditions showed that the particle temperature is the most decisive parameter on the calculated ignition delay time.
1 January 2012 in The Proceedings of the International symposium on diagnostics and modeling of combustion in internal combustion engines
Since the technology of direct injected engines has become more and more prevalent, combustion anomalies such as pre-ignition events have been occurring with increasing frequency. The interaction between the fuel-spray and the oil wetted cylinder liner is considered to be a partial cause for these phenomena. The incoming fuel jet can lead to a detachment of secondary droplets, which may affect pre-ignition events due to their changed flammability properties. To characterize these secondary droplets, spatially and temporally highly resolved optical investigations on the fuel-oil-film-interaction are carried out in this work. Using laser induced fluorescence and two high-speed cameras both fluids are optically separated. Thereby the secondary droplets can be detected and characterized in size, velocity vector, and composition.