We discuss a fundamentally new approach for the measurement of electric (E) fields that will lead to the development of a broadband, direct SI-traceable, compact, self-calibrating E-field probe (sensor). This approach is based on the interaction of radio frequency (RF) fields with alkali atoms excited to Rydberg states. The RF field causes an energy splitting of the Rydberg states via the Autler-Townes effect and we detect the splitting via electromagnetically induced transparency. In effect, alkali atoms placed in a vapor cell act like an RF-to-optical transducer, converting an RF E-field strength measurement to an optical frequency measurement. We demonstrate the broadband nature of this approach by showing that one small vapor cell can be used to measure E-field strengths over a wide range of frequencies: 1 GHz to 500 GHz. The technique is validated by comparing experimental data to both numerical simulations and far-field calculations for various frequencies. We also discuss various applications, including: a direct traceable measurement, the ability to measure both weak and strong field strengths, compact form factors of the probe, and sub-wavelength imaging and field mapping.
We present a technique for measuring radio-frequency (RF) electric field strengths with sub-wavelength resolution. We use Rydberg states of rubidium atoms to probe the RF field. The RF field causes an energy splitting of the Rydberg states via the Autler-Townes effect, and we detect the splitting via electromagnetically induced transparency (EIT). We use this technique to measure the electric field distribution inside a glass cylinder with applied RF fields at 17.04 GHz and 104.77 GHz. We achieve a spatial resolution of ≈100 μm, limited by the widths of the laser beams utilized for the EIT spectroscopy. We numerically simulate the fields in the glass cylinder and find good agreement with the measured fields. Our results suggest that this technique could be applied to image fields on a small spatial scale over a large range of frequencies, up into the sub-terahertz regime.
16 April 2020 in IEEE Transactions on Antennas and Propagation
Radio reception relies on antennas for the collection of electromagnetic fields carrying information, and receiver elements for demodulation and retrieval of the transmitted information. Here we demonstrate an atom-based receiver for AM and FM microwave communication with a 3-dB bandwidth in the baseband of ~100 kHz that provides optical circuit-free field pickup, multi-band carrier capability, and inherently high field sensitivity. The atom-based receiver exploits field-sensitive cesium Rydberg vapors in a centimeter-sized glass cell, and electromagnetically induced transparency, a quantum-optical effect, as a readout of baseband signals modulated onto carriers with frequencies ranging over four octaves, from C-band to Q-band. Receiver bandwidth, dynamic range and sideband suppression are characterized, and acquisition of audio waveforms of human vocals demonstrated. The atomic receiver is a valuable receiver technology because it does not require antenna structures and is resilient against electromagnetic interference, while affording multi-band operation in a single compact receiving element.
In this paper, we demonstrate the detection of millimeter waves via Autler-Townes splitting in 85Rb Rydberg atoms. This method may provide an independent, atom-based, SI-traceable method for measuring mm-wave electric fields, which addresses a gap in current calibration techniques in the mm-wave regime. The electric-field amplitude within a rubidium vapor cell in the WR-10 wave guide band is measured for frequencies of 93.71 GHz and 104.77 GHz. Relevant aspects of Autler-Townes splitting originating from a four-level electromagnetically induced transparency scheme are discussed. We measured the E-field generated by an open-ended waveguide using this technique. Experimental results are compared to a full-wave finite element simulation.
We present a spectral analysis of Rydberg atoms in strong microwave fields using electromagnetically induced transparency (EIT) as an all-optical readout. The measured spectroscopic response enables optical, atom-based electric-field measurements of high-power microwaves. In our experiments, microwaves are irradiated into a room-temperature rubidium vapor cell. The microwaves are tuned near the two-photon Rydberg transition and reach an electric-field strength of , about 20% of the microwave-ionization threshold of these atoms. A Floquet treatment is used to model the Rydberg-level energies and their excitation rates. We arrive at an empirical model for the field-strength distribution inside the spectroscopic cell that yields excellent overall agreement between the measured and calculated Rydberg EIT-Floquet spectra. Using spectral features in the Floquet maps, we achieve an absolute strong-field measurement precision of 6%.
In this work, we demonstrate an approach for improved sensitivity in weak radio frequency (RF) electric-field strength measurements using Rydberg electromagnetically induced transparency (EIT) in an atomic vapor. This is accomplished by varying the RF frequency around a resonant atomic transition and extrapolating the weak on-resonant field strength from the resulting off-resonant Autler-Townes (AT) splittings. This measurement remains directly traceable to SI compared to previous techniques, precluding any knowledge of experimental parameters such as optical beam powers as is the case when using the curvature of the EIT line shape to measure weak fields. We use this approach to measure weak RF fields at 182 GHz and 208 GHz demonstrating improvement greater than a factor of 2 in the measurement sensitivity compared to on-resonant AT splitting RF electric field measurements.