25 July 2025 in RSC Advances
The rheological properties and screen-printing behavior of silver paste on the front side of solar cells are critical for achieving high-resolution electrode patterns.
14 February 2024 in RSC Advances
Environmental protection mandates have spurred the widespread adoption of lead-free glass in electronic material adhesion. Glass powder, crucial for solar silver paste, notably affects the ohmic contact at the Ag–Si interface of crystalline silicon solar cells. This study examines how TeO2 content influences the high-temperature flowability and wettability of lead-free Bi2O3–TeO2-based glass powder, alongside the interplay between the glass's thermal properties and interface contact. Additionally, it investigates the Bi2O3–TeO2 ratio's impact on current transmission through the interfacial glass layer. Experimental results show that the synthesized glass powder exhibits superior high-temperature flowability and wettability, with a low contact resistance of 1.5 mΩ cm2 in silver paste applications. This study also proposes an optimal approach for enhancing current transmission through the interfacial glass layer. Consequently, this glass powder is highly valuable for c-Si solar cell silver paste applications, offering novel insights into improving current transmission efficiency.
1 May 2024 in Materials Research Express
The investigation of conductive silver pastes and inks has witnessed extensive research within the domain of printed electronics in recent years, primarily owing to the exceptional electrical conductivity and steadfastness intrinsic to silver. This paper introduces an approach for the fabrication of stable, cost-effective, and low-resistance conductive silver paste tailored for flexible printed circuits. This method facilitates the solidification of the conductive silver paste into a highly conductive silver film at a curing temperature of 250 °C. In the process of preparing the conductive silver paste, Ag flakes is subject to modification through the incorporation of Ag NPs, which are subsequently sintered at a low temperature curing setting. The sintering of Ag NPs serves to establish connections between adjacent particles of Ag flakes within the paste, thereby enhancing the conductivity and flexibility of the resulting conductive printed silver film. When the ratio of Ag NPs to Ag flakes is maintained at 10:90, the volume resistivity of the Ag NPs-modified film registers at 2.7 × 10−5 Ω.cm. This demonstrates a substantial 53.45% reduction in the volume resistivity of the conductive printed silver film modified with Ag NPs, compared to its Ag NPs-absent counterpart. Post 200 cyclic bending tests, it becomes evident that the resistance change rate in the Ag NPs-modified conductive printed silver film is a mere 12.5%, whereas the Ag NPs-modified silver film lacking Ag NPs displays a resistance change rate of 21.5%. This discrepancy underscores the capacity of Ag NPs-modified Ag flakes to fortify the bending resistance of the conductive printed silver film. Comprehensive data analysis substantiates that the improvements in electrical conductivity and bending resistance can be attributed to the superior bridging facilitated by the sintering process on the surface of the Ag NPs-modified Ag flakes.
21 May 2025 in RSC Advances
As electronic devices become more compact and power-dense, the demand for efficient thermal management materials continues to rise. To address the common issues in conventional thermally conductive composites—namely, poor filler dispersion, high interfacial thermal resistance caused by binders, and complex fabrication processes—this study proposes a novel strategy for constructing binder-free three-dimensional hexagonal boron nitride thermal networks (3D BN) within a polydimethylsiloxane (PDMS) matrix. By leveraging the decomposition behavior of ammonium bicarbonate (NH4HCO3), this approach enables the fabrication of composites with enhanced thermal conductivity and simplified processing. The 3D BN/PDMS composites were prepared via a straightforward process involving blending, cold pressing, drying, and vacuum impregnation. Characterization and testing reveal that the 3D BN thermal network and BN particle size are critical factors influencing the composites' TCs. The resulting 3D BN/PDMS composites exhibit an outstanding TC of 3.889 W m−1 K−1 when the BN particle size is 20 μm and the filler content is 40.70 vol%. This study offers a novel approach to designing and developing high-performance thermally conductive composites, with significant potential for practical applications.