1 August 2021 in Steel in Translation
New information regarding physical-chemical processes in the cavity of converter during top blowing of the bath by groups of supersonic and sonic oxygen je
10 May 2020 in Metal and Casting of Ukraine
Modern technological route of converter production of qualitative iron-carbon semi-product in raw material and energy conditions of Ukraine
1 September 2021 in Steel in Translation
The issues of development and improvement of multipurpose structures of oxygen lances and methods of combined blowing of a converter bath with supply of mu
3 December 2024 in Collection of scholarly papers of Dniprovsk State Technical University (Technical Sciences)
Preheating of scrap in the converter is an actual area of research in modern metallurgy. The growing requirements for energy efficiency and the reduction of raw material costs encourage the development of new technological solutions to increase the share of scrap metal in the charge of converter production. Traditional methods are often limited to the use of no more than 25% of scrap, which is associated with difficulties in its uniform heating and the possible formation of a liquid phase as a result of local overheating. The work evaluates the effectiveness of traditional and experimental technological solutions, such as two-tier and fuel-oxygen nozzles. The stages of ignition and burning of lump coal and pulverized coal fuel and their influence on the uniformity of scrap heating were studied. Experimental studies have shown that with a specific oxygen consumption of 1-1.35 m³/kg of pulverized coal fuel, uniform heating of scrap metal is ensured without the risk of melting the upper layers. During the use of a fuel-oxygen lance, the following features of heating scrap metal using pulverized coal fuel, which was blown in an oxygen ring shell, were discovered: - during the combustion of coal dust in an oxygen environment, due to the significant total surface of coal particles, the bulk of volatile СmНn does not have time to separate before the beginning particle ignition, and carbon burns at the same rate as volatiles. This contributes to the formation of high-temperature torches with great luminosity, which effectively affect the surface of the scrap; - the coefficient of use of blown oxygen and pulverized coal fuel is significantly higher than when using lump gas coal during heating of any duration. This is due to the greater luminosity of the formed torches, which contributes to the intensive absorption of thermal energy by the surface of the scrap; - the time required to heat the surface of the scrap metal to the specified temperature is reduced, which allows you to avoid the formation of a liquid component that can lead to undesirable consequences, such as uneven heating or damage to the converter lining. Based on the results of experimental studies, the relationship between the specific oxygen consumption and the flame temperature was established. The ability to control the temperature regime during the heating of scrap metal indicates the prospects of using a fuel-oxygen nozzle made of PVP to optimize the converter production process. For the full implementation of the technology, additional research and industrial testing are needed to optimize processes and increase production efficiency.
1 June 2017 in Steel in Translation
Nontraditional systems developed and introduced at PAO ArcelorMittal Krivoi Rog permit greater resource and energy conservation in the application of slag coatings to converter linings.
1 January 2019 in Fundamental and applied problems of ferrous metallurgy
The aim of the study is to study the characteristics of physicochemical processes in the cavity of an oxygen converter when purging a bath through two-tier tuyeres of various designs. The analysis showed that the classical designs of oxygen tuyeres equipped with tips with Laval nozzles do not always satisfy the requirements of the technology. The article presents the results of laboratory high-temperature modeling of the process of purging the converter bath through two-tier tuyeres equipped with tips of various designs. The studies were carried out on a multipurpose installation mounted on the basis of a 150-kg induction furnace and a 60-kg converter manufactured at a scale of 1:18 relative to 160 tons of an industrial unit. It is shown that the use of a two-tier lance provides additional advantages for the smelting process. So, in the initial and main periods of purging the converter bath through a two-tier lance with a double-row tip, it was possible to accelerate the process of slag formation without the addition of fluorspar, to intensify the removal of phosphorus at a high carbon content. Upon completion of the initial purge period at a low metal temperature of 1300-1330 ° C and the corresponding basicity of liquid slag, the degree of dephosphorization of 73.3-79.1% is achieved. When used for blowing two-tier tuyeres with double-row tips, the efficiency of afterburning of CO exhaust gases to CO2 also increases at the same decarburization rate of the bath. Based on the data of high-temperature modeling, the rational design of the two-tier lance has been determined, which ensures: balance of the heat balance; yield increase; creating conditions for the removal of phosphorus at a high carbon content; exclusion of negative effects on the lining.