Simon Leijonmarck

Simon Leijonmarck

Auto-generated profile, based on publicly available information

Simon Leijonmarck

Applied Electrochemistry, Department of Chemical Engineering , KTH Royal Institute of Technology , 100 44 Stockholm , Sweden

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 February 2013 in Journal of Materials Chemistry A
Verified
Journal Article
Open access
PDF file
SLSimon Leijonmarck
Simon Leijonmarck
ACAnn Cornell
Ann Cornell
GLGöran Lindbergh
Göran Lindbergh
LWLars Wågberg
Lars Wågberg
Recently, a need for mechanically flexible and strong batteries has arisen to power technical solutions such as active RFID tags and bendable reading devices. In this work, a method for making flexible and strong battery cells, integrated into a single flexible paper structure, is presented. Nano-fibrillated cellulose (NFC) is used both as electrode binder material and as separator material. The battery papers are made through a paper-making type process by sequential filtration of water dispersions containing the battery components. The resulting paper structure is thin, 250 μm, and strong with a strength at break of up to 5.6 MPa when soaked in battery electrolyte. The cycling performances are good with reversible capacities of 146 mA h g−1 LiFePO4 at C/10 and 101 mA h g−1 LiFePO4 at 1 C. This corresponds to an energy density of 188 mW h g−1 of full paper battery at C/10.

1 December 2013 in Composites Science and Technology
Verified
Journal Article
Closed access
SLS. Leijonmarck
S. Leijonmarck
TCT. Carlson
T. Carlson
GLGöran Lindbergh
Göran Lindbergh
LALeif Asp
Leif Asp
HMH. Maples
H. Maples
ABAlexander Bismarck
Alexander Bismarck

27 May 2016 in Journal of the Electrochemical Society
Verified
Journal Article
Open access
PDF file
JHJohan Hagberg
Johan Hagberg
SLSimon Leijonmarck
Simon Leijonmarck
GLGöran Lindbergh
Göran Lindbergh
Carbon fibers have the combined mechanical and electrochemical properties needed to make them particularly well suited for usage as electrodes in a structural lithium-ion battery, a material that simultaneously works as a battery and a structural composite. Presented in this paper is an evaluation of commercial polyacrylonitrile-based carbon fibers in terms of capacity and coulombic efficiency, as well as a microstructural and surface evaluation. Some polyacrylonitrile based carbon fibers intercalate lithium ions, resulting in a similar capacity as state-of-the-art graphite based electrodes, presently the most commonly used negative electrode material. Using high precision coulometry, we found a capacity of around 250–350 mAh/g and a very high coulombic efficiency of over 99.9% after ten cycles, which is even higher than a commercial state-of-the art graphitic electrode evaluated as reference. The high coulombic efficiency is attributed to the very low surface area of the carbon fibers, resulting in a small and stable solid-electrolyte interface layer. A highly graphitized ultra high modulus carbon fiber was evaluated as well and, compared to the other fibers, less lithium was inserted (corresponding to approximately 150 mAh/g). We show that the use of carbon fibers as an electrode material in a structural composite battery is indeed viable.

25 February 2016 in Materials
Verified
Journal Article
Open access
PDF file
HLHuiran Lu
Huiran Lu
ACAnn Cornell
Ann Cornell
FJFernando Alvarado Jacobs
Fernando Alvarado Jacobs
MBMårten Behm
Mårten Behm
SLSimon Leijonmarck
Simon Leijonmarck
GLGöran Lindbergh
Göran Lindbergh
The industrial lignin used here is a byproduct from Kraft pulp mills, extracted from black liquor. Since lignin is inexpensive, abundant and renewable, its utilization has attracted more and more attention. In this work, lignin was used for the first time as binder material for LiFePO4 positive and graphite negative electrodes in Li-ion batteries. A procedure for pretreatment of lignin, where low-molecular fractions were removed by leaching, was necessary to obtain good battery performance. The lignin was analyzed for molecular mass distribution and thermal behavior prior to and after the pretreatment. Electrodes containing active material, conductive particles and lignin were cast on metal foils, acting as current collectors and characterized using scanning electron microscopy (SEM), electrochemical impedance spectroscopy (EIS) and galvanostatic charge-discharge cycles. Good reversible capacities were obtained, 148 mAh·g−1 for the positive electrode and 305 mAh·g−1 for the negative electrode. Fairly good rate capabilities were found for both the positive electrode with 117 mAh·g−1 and the negative electrode with 160 mAh·g−1 at 1C. Low ohmic resistance also indicated good binder functionality. The results show that lignin is a promising candidate as binder material for electrodes in eco-friendly Li-ion batteries.

1 September 2013 in Nano Energy
Verified
Journal Article
Closed access
SLSimon Leijonmarck
Simon Leijonmarck
ACAnn Cornell
Ann Cornell
GLGöran Lindbergh
Göran Lindbergh
LWLars Wågberg
Lars Wågberg

17 June 2014 in Journal of Materials Chemistry A
Verified
Journal Article
Open access
PDF file
MWM. Willgert
M. Willgert
SLS. Leijonmarck
S. Leijonmarck
GLGöran Lindbergh
Göran Lindbergh
EME. Malmström
E. Malmström
MJM. Johansson
M. Johansson
The present study describes the synthesis and characterization of a series of four composite electrolytes for lithium ion battery applications. The two-phase electrolytes are composed of a soft, ionic conductive poly(ethylene glycol) (PEG) matrix having stiff nanofibrillated cellulose (CNF) paper as reinforcement to provide mechanical integrity. The reinforcing CNF is modified in order to create covalent bonds between the phases which is particularly beneficial when swelling the composite with a liquid electrolyte to enhance the ionic conductivity. After swelling the composite polymer electrolyte, forming a gelled structure, values of ionic conductivity at 5 × 10−5 S cm−1 and an elastic modulus around 400 MPa at 25 °C are obtained.