9 December 2020 in Eastern-European Journal of Enterprise Technologies
Patternsin the synthesis processes, the microstructure and properties of strontium-anorthite ceramics modified by glass of spodumene composition
30 June 2023 in Eastern-European Journal of Enterprise Technologies
This paper reports research into the development of compositions of engobe coatings for ceramic bricks and investigating the influence of technological production factors on their physical and mechanical properties. The results of this work make it possible to solve the task of expanding the range and improving the operational properties of building ceramics. The data obtained have made it possible to establish physicochemical processes occurring during the formation of the phase composition and structure of engobe coatings. This has revealed the possibilities for designing engobe for various types of ceramic bricks, which differ in technological parameters of production and operational properties. The charge compositions were designed in a three-component system "refractory clay – quartz sand – cullet", taking into account the possibility of their practical implementation in large-tonnage production. It has been established that the most important condition for obtaining high-quality products is the correlation of shrinkage and temperature coefficients of linear expansion of the ceramic shard and engobe coating. To prevent various defects, these indicators should vary by no more than 10 %. The crystal-phase composition of engobe is represented by b-quartz and a small amount of devitrite, which are evenly distributed in a vitreous dense layer of coating on the surface of the ceramic shard. Distinctive features of the results relate to the fact that a solution to the problem of designing engobe coatings for ceramic bricks has been proposed and the physicochemical bases of production have been highlighted. This paper also suggests ways to achieve coordination of finely dispersed coatings with coarse-grained ceramic masses by shrinkage and thermal processes. The results reported here could be applied in typical production of face, clinker, and in some cases – ordinary brick or ceramic stone with firing temperatures of 950–1150 °C
1 March 2021 in Urban development and spatial planning
The article is devoted to the formation of recreational facilities in the structure of suburban areas, which are favorable for the development of recreational and tourist activities. The main preconditions and factors influencing the formation of certain types of institutions are studied. The main architectural and planning features of recreational facilities are identified. The main architectural techniques for the formation of recreational institutions are determined. Such techniques are the pavilion and block-pavilion structure. The main functional groups of the premises of the recreational complexes have been determined. The main groups of premises include: summer residential buildings, sports and recreation facilities, cultural and social facilities, catering facilities. The optimal natural conditions for the formation of recreational institutions in the Sumy region have been determined. A study of natural and recreational resources of the Lebedyn district in Sumy region is conducted. It is established that in this area there are optimal conditions for the formation of recreational facilities. Taking into account certain natural conditions and factors, the concept of the project solution of the recreational and recreational complex in the Lebedyn district of Sumy region is proposed. The complex is proposed to be designed in the coastal zone of the river Psel. The methods of urban planning, architectural planning and compositional solutions that are optimal for a given area were established in the process of project search. These techniques include: the reception of accommodation in a suburban recreational area, the reception of a combined compositional planning organization, the reception of folk (traditional) Ukrainian architecture in combination with modern structural systems.
31 October 2023 in Eastern-European Journal of Enterprise Technologies
Screw conveyors are used to move bulk materials vertically upwards, horizontally, and at an angle to the horizon. The processes that take place when particles are moved by a screw conveyor in vertical and horizontal directions have been studied. There is a significant difference between them: for transportation in the vertical direction, the necessary conditions must be ensured (sufficient angular speed of rotation of the screw), and for horizontal transportation, the movement of the particle occurs at any angular speed of rotation of the screw. Therefore, when changing the inclination of the axis of the screw, there comes a moment when transportation becomes possible, while it was impossible in the vertical direction. This paper considers the movement of a particle under the condition that it simultaneously contacts two surfaces: the moving surface of the screw and the stationary surface of the cylindrical casing in which the screw rotates. Their common line along which the particle slides is a helical line – the periphery of the screw. The particle slides along the helical line of the rotating screw, i.e., it is in relative motion with respect to it. At the same time, it slides along the surface of the casing, relative to which it is in absolute motion. The trajectory of the particle's absolute motion is its sliding track on the casing surface. When constructing differential equations of the relative motion of particles, the forces applied to the particle were taken into account. The initial position was taken to be the vertical direction of the screw to transport the particle upwards. If an auger in a cylindrical casing is tilted from the vertical direction to a certain angle, then all applied forces (except the force of weight) will also tilt to this angle. On the basis of this, generalized differential equations of the relative motion of a particle during its transportation by an inclined screw were built. They made it possible to derive a generalized mathematical model of the movement of a particle by an inclined screw that rotates inside a fixed casing
17 May 2024 in Vìsnik Nacìonalʹnogo unìversitetu "Lʹvìvsʹka polìtehnìka". Serìâ Arhìtektura
DUDepartment of Architecture and Engineering Research Sumy National Agrarian University
Department of Architecture and Engineering Research Sumy National Agrarian University
The article provides materials for the analysis of the development of business centers as a specific class of buildings in a modern big city. Examples of eternal and global experience in designing and building business centers of various functional purposes are given. Various trends and directions in the process of design and construction of business center buildings in Ukraine and foreign countries were studied. Тhe interrelationship of the quality of spatial planning and visual solutions of these objects with the demand for them on the market and their further development prospects is considered. . Considered various options for the formation of business center buildings in the existing urban planning conditions of settlements. The main architectural and planning schemes and compositional techniques in the design of such buildings are defined. As a practical experience, the project proposal of a business center building in the central part of the Sumy city was considered, and its functional and planning structure was analyzed. The scientific novelty and practical significance of this work lies in the fact that the main trends of the architectural and planning organization of modern business centers, as centers of business and economic activity in a large city, are determined, and the priority directions for the formation of the functional structure of such objects are outlined both in modern realities and for the future
30 August 2025 in Eastern-European Journal of Enterprise Technologies
This study’s object is the process of designing closed non-circular wheels with a given center-to-center distance with external rolling, provided that it occurs without mutual slip. Non-circular wheels serve as centroids in the design of cylindrical gear transmissions with a variable gear ratio. The gear ratio is characterized by the gear function. If the gear ratio is constant, then the centroids are circles. The gear ratio in this case is the ratio of the radii of these circles. Non-circular wheels can be designed according to a given gear function, which is determined by the kinematics of the mechanism’s links’ actuators. In this case, non-circular wheels can be non-closed. The study addresses another task related to designing non-circular wheels provided that they are closed. Various approaches can be used to this end. The current paper considers the use of a fourth-degree polynomial. In non-circular wheels, the radii, which are understood as the distances from the centers of rotation to the point of contact, are variable. The necessary conditions for constructing non-circular wheels are the constant value of the sum of these radii during the rotation of non-circular wheels, as well as the equality of the paths traveled, that is, the equality of the arcs that non-circular wheels pass during rotation. Pairs of wheels can have the same or different numbers of protrusions and depressions. This is explained by the use of a fourth-degree polynomial whose plot has an axis of symmetry. Accordingly, non-circular wheels or their protrusions also have an axis of symmetry. As an example, the construction of a leading centroid with one protrusion and one depression is given, for which the maximum and minimum distances from the center are 10 and 6.1 linear units, respectively. For this centroid, a trailing centroid has been constructed, and the center-to-center distance has been found, which is 16.79 linear units