17 April 2018 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
This paper presents an 8-bit 320-MS/s successive approximation register (SAR) analog-to-digital converter (ADC) with the linearity-improved technique. A linearity-improved sampling switch with parasitic capacitance compensation, which makes the parasitic capacitance of sampling switch to be almost constant with varied input signal, is proposed. It also improves the matching of the differential sampling switches. Moreover, a metastability immunity technique is provided to suppress the uncertain decision behavior of dynamic comparator at high conversion rate. In addition, a bypass SAR logic that parallels comparator and SAR logic operations is exhibited to reduce the delay of SAR feedback loop. To demonstrate the proposed techniques, a design example of SAR ADC is fabricated in a 55-nm CMOS technology, consuming 1.2 mW at a 1-V power supply. It achieves a signal-to-noise-and-distortion ratio > 43.5 dB and spurious free dynamic range > 54 dB at 320 MS/s. The ADC core occupies an active area of only 0.02 mm², and the corresponding figure of merit is 30 fJ/conversion step with Nyquist rate.
6 May 2019 in IEEE Transactions on Very Large Scale Integration (VLSI) Systems
This paper presents a linearity-enhanced 10-bit 160-MS/s successive approximation register (SAR) analog-to-digital converter (ADC) with a high-speed and low-noise comparator. A p-well floating technique for linearity improvement of sampling switch is proposed. The total parasitic capacitance of the sampling switch is depressed compared to conventional structures. Also, the variation of parasitic capacitance is reduced. Furthermore, a substrate voltage boosting technique is proposed to depress the noise of comparator at a high conversion rate. In addition, an improved parallel SAR logic is exhibited to increase the speed of SAR feedback loop and enhance the settling of digital-to-analog converter (DAC). Last, an adaptive sampling technique is utilized to increase the sampling time of SAR ADC. The proposed SAR ADC is fabricated in the 65-nm CMOS process, consuming 2 mW at a 1.2-V power supply. It achieves a signal-to-noise distortion ratio (SNDR) > 55.6 dB and spurious-free dynamic range (SFDR) > 69 dB at 160 MS/s. The ADC core occupies an active area of 0.023 mm², and the corresponding figure-of-merit (FoM) is 25.4 fJ/conversion-step at Nyquist input.
3 August 2018 in Journal of Circuits, Systems and Computers
31 July 2019 in Journal of Circuits, Systems and Computers
8 August 2020 in Journal of Circuits, Systems and Computers
1 April 2017 in Journal of Semiconductors
A 10-bit 110 MHz SAR ADC with asynchronous trimming is presented. In this paper, a high linearity sampling switch is used to produce a constant parasitical barrier capacitance which would not change with the range of input signals. As a result, the linearity of the SAR ADC will increase with high linearity sampled signals. Farther more, a high-speed and low-power dynamic comparator is proposed which would reduce the comparison time and save power consumption at the same time compared to existing technology. Additionally, the proposed comparator provides a better performance with the decreasing of power supply. Moreover, a highspeed successive approximation register is exhibited to speed up the conversion time and will reduce about 50% register delay. Lastly, an asynchronous trimming method is provided to make the capacitive-DAC settle up completely instead of using the redundant cycle which would prolong the whole conversion period. This SAR ADC is implemented in 65-nm CMOS technology the core occupies an active area of only 0.025 mm and consumes 1.8 mW. The SAR ADC achieves SFDR > 68 dB and SNDR > 57 dB, resulting in the FOM of 28 fJ/conversion-step. From the test results, the presented SAR ADC provides a better FOM compared to previous research and is suitable for a kind of ADC IP in the design SOC.