2 June 2021 in IEEE Transactions on Vehicular Technology
With the increase in the capacity and power rating of batteries in today's HEVs and EVs, the battery thermal management (BTM) system bears growing importance in vehicle safety and efficiency. A practical BTM system is commonly coupled with the passenger cabin heating-ventilation-air-conditioning (HVAC) system, which makes a major energy consumer and a challenging control object. Thanks to the connected and automated vehicle (CAV) technology, predictions of the vehicle speed profile and power trajectory can be obtained, providing the possibility for predictive control of the BTM and HVAC coupled system in order to maintain battery safety, passenger comfort, and to reduce energy consumption. However, the tradeoff among higher energy saving potential and wider control range from a long and sparse horizon, and higher accuracy from a short and dense horizon is inevitable in the conventional predictive control. In this paper, a two-layer predictive control strategy for warm/hot weather is proposed to address the aforementioned tradeoff. The upper layer controller firstly plans the optimized battery temperature trajectory according to the look-ahead speed preview and battery power profiles provided by the CAV network and the integrated BTM and HVAC system efficiency surface from off-line data. Then the lower layer model predictive controller tracks the planned trajectory and cabin temperature reference while enforcing the energy consumption optimization. Simulation results demonstrate that the proposed strategy exhibits accurate battery and passenger cabin temperature reference tracking while achieving up to {\color{red}10.47\% HVAC energy saving comparing to a baseline control strategy with UDDS profile and typical driving conditions}. Implementation of the proposed strategy on a real-time vehicle emulator based on rapid control prototyping (RCP) and hardware-in-the-loop (HIL) platforms demonstrates the real-world implementation capability of the proposed two-layer framework.
16 May 2019 in IEEE Transactions on Power Electronics
In this paper, a battery balancing circuit is proposed for the series-connected lithium-ion battery cells based on the principle of synchronous rectification. The proposed balancing circuit, also referred to as an equalizer, mainly includes a buck–boost converter (BBC), a multiport half-bridge converter (MHBC), and a driving circuit. The MHBC is coupled with a multiwinding transformer. Compared with the conventional congeneric methods, the number of transformer windings is almost reduced by half, leading to a more compact size and lower cost. Moreover, the secondary mosfet s of the MHBC are synchronously driven by the primary half-bridge converter (HBC) without the need of additional isolated mosfet gate drivers and power supplies, dramatically reducing the circuit cost and complexity. In addition, the proposed equalizer can realize the module-to-multi-cell (M2MC) equalization under severe imbalance conditions to improve the balancing speed, and work at the any-cell-to-any-cell (AC2AC) self-balancing mode under slight imbalance conditions to improve the balancing efficiency and effectiveness, which achieves a good trade-off between balancing speed and effectiveness. The expressions of the equalization current and efficiency are derived and verified by experimental results. The proposed equalizer is experimentally evaluated for a string with 12 series-connected lithium-ion cells.
26 August 2021 in IEEE Transactions on Intelligent Transportation Systems
The battery thermal management (BTM) system plays an increasingly important role today in the safety of electric vehicles (EVs) and hybrid electric vehicles (HEVs) as the battery capacity and power ratings keep growing. The BTM system is commonly coupled with the vehicle passenger cabin HVAC system. This integrated thermal system is a major onboard energy consumer, and its complexity brings challenges to its control. With the planned-ahead speed profile and the corresponding power trajectory obtained from the connected and automated vehicle (CAV) technology, predictive control makes a desirable option for the integrated system to maintain battery safety and passenger comfort while lowering energy consumption. However, in order to achieve both high accuracy and low cost in a wide control range, a very long prediction horizon and high sampling rate are both necessary. This will overwhelm the processing capacity of the onboard electronic control unit (ECU) if using conventional predictive control. In this paper, a two-stage predictive control strategy for the BTM and HVAC coupled system is proposed to solve this problem. In stage 1, based on the integrated cooling system efficiency features, a hierarchical and iterative dynamic programming (HIDP) scheme is designed to derive the optimal battery temperature trajectory to reach the set point at the end of the horizon with a modest computation burden. In stage 2, a control-oriented model is constructed for the cooling system and a model predictive controller (MPC) is accordingly built to track the trajectory from Stage 1 while enforcing the energy saving. A high set-point-tracking performance and as high as 10.61% energy saving for the cooling system in the UDDS cycle are verified by simulation results. The real-time implementation capability of the proposed strategy is demonstrated by the vehicle emulator experiments based on hardware in the loop (HIL) and a rapid control prototyping (RCP) platform.
23 October 2017 in IEEE Transactions on Vehicular Technology
DC-link voltage fluctuation, originated from the single-phase power supply, has a significant impact on the railway traction drive system. Instead of employing a large LC filter to suppress the fluctuation, software solutions are of more interests, since they do not add additional components to the system. A state-of-the-art feedforward strategy predicts the dc-link voltage pattern based on its repetitive nature and directly modifies the duty cycle fed to the inverter to eliminate the impact of the fluctuation. Yet this strategy requires a symmetrical and consistent pulse pattern. In this paper, a compensation approach for synchronous space vector modulation with multiple pulse patterns is proposed. It utilizes the prediction of the dc-link voltage pattern and, based on the volt-second balancing principle, modifies the switching instants corresponding to different pulse patterns. Simulation and experimental results show that the proposed method can significantly eliminate the impact of the fluctuation.
20 February 2020 in IEEE Transactions on Power Electronics
In railway traction applications, the six-step operation of traction inverters is frequently applied at high speed due to the limitation of switching frequency of the converter which is installed in very limited space on the train. Meanwhile, without hardware filters installed, fluctuation components of dc-link voltage will emerge due to the input power ripple introduced by the single phase rectifier, and can cause significant current and torque ripple in the motor. In this paper, a direct torque control scheme for permanent magnet synchronous motor (PMSM) in six-step operation is proposed to suppress the dc-link voltage fluctuation induced current and torque ripple without extra hardware. It adjusts the duration of voltage space vectors according to the predicted dc-link voltage waveform six times per fundamental cycle, and minimizes the error between output torque and reference torque at the end of each time. Experimental results on an interior permanent magnet synchronous motor (IPMSM) demonstrate that the proposed control can more effectively suppress current and torque ripple than states of the art and achieve torque control with high dynamic and accuracy.