Olumuyiwa Ajani Lasode

Olumuyiwa Ajani Lasode

Auto-generated profile, based on publicly available information

Olumuyiwa Ajani Lasode

Department of Mechanical Engineering, University of Ilorin, Ilorin, Kwara State, Nigeria

Research Focus & Metrics

Academic Career Length

23Years (2004-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2020 in Heliyon
Verified
Journal Article
Open access
Adekunle A. AdelekeAdekunle A. Adeleke
Adekunle A. Adeleke
JOJ.K. Odusote
J.K. Odusote
PIPeter Ikubanni
Peter Ikubanni
OLO.A. Lasode
O.A. Lasode
MMM. Malathi
M. Malathi
DPD. Paswan
D. Paswan
The impact of torrefaction temperature on the ignitability, fuel ratio and ash fusion temperatures of two tropical deciduous woods (Teak and Melina) were investigated in a setup of tubular furnace. The properties considered are calorific value, fuel ratio, ignitability index, ash compositions and ash fusion temperatures of the biomass. Six different temperatures (220, 240, 260, 280, 300 and 320 °C) at 60 min reaction time were considered. The results indicated that as torrefaction temperature increased, the calorific value, fuel ratio and ignitability index of the biomass also increased. The ignitability index of biomass (40-63) was better than the value (35) recommended for fuel applicable in thermal plants for power generation. The ash compositional analysis revealed that there was no variation in the quantity of SiO2, Al2O3, CaO along with other minerals for the raw and torrefied biomass. This implied that the temperature up to 320 °C has no significant impact on the compositions of biomass ash during torrefaction. The ash fusion temperature test showed that the biomass ash softens at ≈ 1200 °C and finally fused at ≈ 1300 °C. The study concluded that an increase in torrefaction temperature increases the thermal properties of the torrefied biomass without affecting the compositions of biomass ash or lowering the ash fusion temperatures.

1 March 2014 in Bioresource Technology
Verified
Journal Article
Closed access
ABA.O. Balogun
A.O. Balogun
OLO.A. Lasode
O.A. Lasode
AMA.G. McDonald
A.G. McDonald

9 February 2017 in Biofuels
Verified
Journal Article
Closed access
JOJ.A. Oyebanji
J.A. Oyebanji
POP.O. Okekunle
P.O. Okekunle
OLO.A. Lasode
O.A. Lasode
SOS.O. Oyedepo
S.O. Oyedepo
In this study, bio-oils from fast pyrolysis of West African cordia (Cm) and Africana birch (Al) sawdust were analyzed using a gas chromatography-mass spectrometry (GC-MS) analyzer. The chemical composition of bio-oil was analyzed for quality, stability or suitability for downstream upgrading. Proximate and elemental analyses were carried out using iso-conversional methods and gas chromatography/mass spectrometry (Py-GC/MS) technique, respectively. Results of the study show that volatile matter, fixed carbon, ash content and moisture content of Cm and Al are 80.03, 10.25, 1.70% and 8.02%, and 75.83, 10.28, 3.81% and 10.08%, respectively. The results of the elemental analysis show that the contents of carbon, hydrogen, nitrogen, oxygen and sulfur for Cm and Al are 24.76, 3.00, 0.70, 70.57 and 0.97%, and 29.20, 0.44, 0.88, 68.15 and 1.33%, respectively. The higher heating value (HHV) of the bio-oil, bio-char and pyro-gas obtained from the biomass samples ranged from 64.35 to 66.65 MJ/kg, 18.95 to 22.25 MJ/kg and 20.45 to 23.65 MJ/kg, respectively. Results of analytical Py-GC/MS showed that the proportion of phenolic compounds identified is more than 50%, with trans-2-octadecadecen-1-ol, cis-10-pentadecen-1-ol, 9-octadecenal, methyl-1-cyclohexenyl ketone showing dominance. This study established that pyro-fuel not only can be used as fuel but can also be purified and serve as raw materials for chemical and processing industries.

1 July 2019 in Heliyon
Verified
Journal Article
Open access
Adekunle A. AdelekeAdekunle A. Adeleke
Adekunle A. Adeleke
JOJ.K. Odusote
J.K. Odusote
OLO.A. Lasode
O.A. Lasode
PIPeter Ikubanni
Peter Ikubanni
MMM. Malathi
M. Malathi
DPD. Paswan
D. Paswan
Coal processing industries generate millions of tons of fines (<3 mm) during mining operation and are often considered as wastes. These wastes have enormous potential in serving as energy and metallurgical operation feedstock. One avenue for its use is densification into briquettes or pelletizes. Various briquetting techniques have been adopted in the past few decades; however, the main issues upfront in commercializing these techniques are significant binder cost and poor mechanical integrity. Therefore, the present study concentrates on utilizing commonly available organic binder along with pretreated biomass in developing coal fine briquettes. Briquettes were produced after initial pretreatment of the raw materials under a load of 2 tons. Briquettes were cured in an inert environment and eventually characterized for its main litmus requirements (physical properties). It was observed that pitch-molasses bonded briquettes have better physical properties leading to good mechanical integrity than briquettes produced from individual binder. The proximate, ultimate and calorific value analyses of the briquettes do not deteriorate but mildly improved compared to the raw coal fines. With a density of 1.18-1.32 g/cm3, drop to fracture that is greater than 100 (times/2 m), impact resistance index well above 6000, water resistance index of 99% and cold crushing strength of 9 MPa, pitch-molasses bonded briquettes clearly surpassed recommended physical properties benchmarked for briquettes of industrial and domestic end use. The physical properties of the briquettes favorably meet requirements as feedstock for rotary kiln direct reduced iron and COREX iron-making processes as well as fuel for thermal operations.

1 September 2014 in Journal of Analytical and Applied Pyrolysis
Verified
Journal Article
Closed access
OLOlumuyiwa A. Lasode
Olumuyiwa A. Lasode
ABAyokunle O. Balogun
Ayokunle O. Balogun
AMArmando G. McDonald
Armando G. McDonald

5 March 2019 in Biomass Conversion and Biorefinery
Verified
Journal Article
Closed access
PDF file
JOJamiu Kolawole Odusote
Jamiu Kolawole Odusote
Adekunle A. AdelekeAdekunle A. Adeleke
Adekunle A. Adeleke
OLOlumuyiwa Ajani Lasode
Olumuyiwa Ajani Lasode
MMMadhurai Malathi
Madhurai Malathi
DPDayanand Paswan
Dayanand Paswan