28 July 2022 in Superconductor Science and Technology
Superconducting undulators (SCUs) with a period >15 mm can offer a much higher on-axis undulator field B 0 than state-of-the-art cryogenic permanent magnet undulators with the same period and vacuum gap. The commissioned NbTi planar SCUs for user operation in the Karlsruhe Institute of Technology synchrotron and the advanced photon source storage ring are operated stably without quenches, producing outperformed photon flux in the high energy part of the hard x-ray spectrum. Another potential advantage of deploying SCU is its radiation hardness, a crucial characteristic for being used in free electron lasers (FELs) driven by high repetition rate superconducting linear accelerators (LINACs) and diffraction limited storage rings (DLSRs) with small vacuum gap and large averaged beam current. The development of shorter period but high field SCU is an important mission in an EU founded CompactLight project as this technology would reduce both the length of undulators and the length of LINACs. This review paper first overviews the research and development of SCUs worldwide from the late 1970s to 2021, then presents the SCU design requirements and compares the theory limits of different types of planar and helical SCUs, and finally reviews the technical challenges including the SCU cryostat, the magnetic field measurement, the integral/local field correction and the high-temperature superconductor (HTS) challenges and prospects the research needs for SCUs.
6 September 2018 in Superconductor Science and Technology
We fabricated three racetrack coils (RC1, RC2, and RC3) from Bi-2212 Rutherford cables (17-strand, thickness × width = 1.44 mm × 7.8 mm, strand diameter = 0.8 mm) and applied overpressure processing heat treatment (OPHT). The quench currents of RC1 and RC2 reached 5268 A and 5781 A, respectively, despite them still, surprisingly, exhibiting some Bi-2212 leakage to the surface. After removing most of the leakages using a simple-to-implement insulation scheme, the quench current of RC3 improved to 6485 A, which is about three times the average quench current of a dozen racetrack coils that had been fabricated and reacted using the conventional 1 bar heat treatment. The results confirm the effectiveness of the OPHT technology and the new leakage control scheme for coils made from Bi-2212 Rutherford cables. Coils exhibited an increased quench current with increasing the current ramp rate from 5 to 200 A s −1 ; they were quite stable against point and transient disturbances, and were capable of adsorbing persistent Joule heating at ∼80 mW for >15 s before quenching. These behaviors are different from Nb–Ti and Nb 3 Sn accelerator magnets. Overall, our results provide a critical evaluation and verification of Bi-2212 wire and magnet technologies (wire, insulation, heat treatment, coil fabrication, and coil operation), reveal crucial new stability features of Bi-2212 magnets, and demonstrate technological options for it to become a practical high-field magnet technology.
15 March 2023 in Superconductor Science and Technology
A 10 mm-period, high-temperature superconducting (HTS) undulator consisting of 20 staggered-array GdBa2Cu3O7−x
(GdBCO) bulk superconductors has been fabricated and tested successfully. Each GdBCO disk was machined into a half-moon shape with micro-meter accuracy and shrink-fitted into a slotted oxygen-free copper disk which provided pre-stress and effective conduction-cooling. The HTS undulator prototype, consisting of GdBCO disks, copper disks, and CoFe poles fitted in a long copper shell, was field-cooled magnetized in fields of up to 10 T at 10 K. An undulator field of 2.1 T in a 4 mm magnetic gap was obtained. This field is the largest reported yet for the same gap and period length and exceeds the target value of 2 T for the meter-long HTS undulator scheduled for the hard x-ray I-TOMCAT beamline in the Swiss Light Source 2.0. We have demonstrated that bulk superconductor based undulators can provide significantly improved performance over alternative technologies.
23 December 2015 in IEEE Transactions on Applied Superconductivity
The Institute of High Energy Physics (Beijing, China) is pursuing R&D of high-field accelerator magnet technology for the recently proposed CEPC-SPPC project, which will need thousands of 20-T level accelerator magnets in 20 years. A long-term plan has been made aiming to realize the 20-T magnets in 15 years. The conceptual design study has been ongoing from 2014 based on the current $\mathbf{J}_{\mathbf{c}}$ level of superconductors. As both Nb 3 Sn and high-temperature superconductor superconducting materials are strain sensitive, the common-coil configuration has been chosen as the first option for the design study of the 20-T dipoles, to simplify the coil structure, raise the bending radius, and lower the strain level in superconducting coils. The magnetic analysis, mechanical analysis, and preliminary design study of the straight section and the coil ends have been completed for a 20-T common-coil dipole magnet. The main characteristics and challenges of this design concept will be presented in this paper.
16 October 2014 in IEEE Transactions on Applied Superconductivity
The Institute of High Energy Physics (IHEP, Beijing, China) is proposing a two-stage particle collider: CEPC-SppC. The first stage is a circular electron-positron collider (CEPC), expected to carry out high-precision studies on Higgs bosons. Upon completion of the CEPC experiment, it will be upgraded to a super proton-proton collider (SppC), aiming at the discovery of physics beyond the standard model. The circumference of the accelerator for CEPC and SppC will be 50 ~ 70 km. The required dipole held strength is 20 T for SppC. As the start of a long-term R&D plan for high-held accelerator magnet technology at IHEP, a 15-T short sample held Nb 3 Sn dipole is planned to be developed within the next five years. The common-coil configuration is adopted to provide space for two apertures with a maximum diameter of 60 mm. The 10 -4 level held uniformity will be reached at a reference radius of 15 mm. Magnetic analytical modeling and FEM cross section study of this high-held common-coil dipole has been done and will be presented here. A preliminary cross section study of the 20-T common-coil dipole will also be introduced; the design is based on the current J c level of Nb 3 Sn and HTS superconductors.
7 October 2020 in Superconductor Science and Technology
A backward computation method has been developed to accelerate modelling of the critical state magnetization current in a staggered-array bulk high-temperature superconducting (HTS) undulator. The key concept is as follows: (i) a large magnetization current is first generated on the surface of the HTS bulks after rapid field-cooling (FC) magnetization; (ii) the magnetization current then relaxes inwards step-by-step obeying the critical state model; (iii) after tens of backward iterations the magnetization current reaches a steady state. The simulation results show excellent agreement with the
H
-formulation method for both the electromagnetic and electromagnetic-mechanical coupled analyses, but with significantly faster computation speed. The simulation results using the backward computation method are further validated by the recent experimental results of a five-period Gd–Ba–Cu–O (GdBCO) bulk undulator. Solving the finite element analysis (FEA) model with 1.8 million degrees of freedom (DOFs), the backward computation method takes less than 1.4 h, an order of magnitude or higher faster than other state-of-the-art numerical methods. Finally, the models are used to investigate the influence of the mechanical stress on the distribution of the critical state magnetization current and the undulator field along the central axis.