Tushar Sathe

Tushar Sathe

Auto-generated profile, based on publicly available information

Tushar Sathe

Visvesvaraya National Institute of Technology

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 September 2017 in Renewable and Sustainable Energy Reviews
Verified
Journal Article
Closed access
TSTushar M. Sathe
Tushar M. Sathe
ADA.S. Dhoble
A.S. Dhoble

1 December 2019 in International Journal of Heat and Mass Transfer
Verified
Journal Article
Closed access
TSTushar Sathe
Tushar Sathe
ADA.S. Dhoble
A.S. Dhoble

1 January 2018 in Applied Solar Energy
Verified
Journal Article
Closed access
PDF file
SJSandeep S. Joshi
Sandeep S. Joshi
ADAshwinkumar S. Dhoble
Ashwinkumar S. Dhoble
TSTushar Sathe
Tushar Sathe
CMChidanand Mangrulkar
Chidanand Mangrulkar
The paper reports use of silicone oil as spectrum filter and heat absorber for photovoltaic thermal systems. The terrestrial solar spectrum is in the wavelength range of 0.25 to 2.5 μm. The response...

1 July 2018 in Journal of Renewable and Sustainable Energy
Verified
Journal Article
Closed access
PDF file
TSTushar M. Sathe
Tushar M. Sathe
ADA. S. Dhoble
A. S. Dhoble
The applicability of phase change materials (PCMs) for the thermal management of low concentrated photovoltaic systems is explored in the current research work. Extended surfaces on the back surface of the PCM container are proposed with its small portion extruded to the outside. PCM thicknesses of 80 mm, 100 mm, and 120 mm are investigated, and an 80 mm thick PCM system is considered as the base configuration. Systems with 2 fins, 3 fins, and 4 fins are analyzed with two different fin lengths of 30 mm and 40 mm inside the PCM enclosure. Two-dimensional transient numerical analysis has been carried out with ANSYS FLUENT using the enthalpy porosity method. The nonuniform melting behavior of PCMs due to natural convection inside the molten PCMs is considered during the analysis using a Boussinesq approximation. The result shows that the proposed 4 fin configuration enhances the melting time by 6000 s compared to the no fin system, reduces the average PCM temperature inside the container by 18%, and decreases the heater surface temperature by 16%.

15 August 2024 in Journal of Advanced Research in Fluid Mechanics and Thermal Sciences
Verified
Journal Article
Open access
PDF file
FSFahim Rahim Sheikh
Fahim Rahim Sheikh
SDSuresh Pandurang Deshmukh
Suresh Pandurang Deshmukh
PAPurushottam Ardhapurkar
Purushottam Ardhapurkar
MHMd Modassir Hussain
Md Modassir Hussain
PWPankaj Wankhede
Pankaj Wankhede
TSTushar Sathe
Tushar Sathe
Photovoltaic thermal (PVT) systems integrated with Nanoparticle Enhanced Phase Change Materials Nanofluid (NePCM-nanofluid) are widely used in solar thermal systems for thermal energy storage, and they significantly improve energy efficiency. Solar thermal systems are particularly viable in the region of high-temperature and variable climatic conditions. It is crucial to understand the NePCM-nanofluid PVT systems' performance in this regard to adapt the technology to the hot regional conditions. Four solar systems—PV, PVT, PVT-PCM, and PVT-NePCM-nanofluid—were tested in Shegaon, Vidarbha, India, under real-time conditions. Integration of PVT-NePCM-nanofluid reduced PV cell temperature by 25.7°C during peak radiation. Comparative analysis revealed electrical efficiencies of 12.40% to 14.50% and thermal efficiencies ranging from 40% to 70%. The experimental analysis has been carried out at varied flow rate of nanofluid and optimal system performance was observed at a 7 LPM flow rate.

30 June 2020
Verified
Book Chapter
Closed access
PDF file
SJSandeep Joshi
Sandeep Joshi
STShubham Tagde
Shubham Tagde
APAboli Pingle
Aboli Pingle
NBNikhil Bhave
Nikhil Bhave
TSTushar Sathe
Tushar Sathe