Baoren Li

Baoren Li

Auto-generated profile, based on publicly available information

Baoren Li

Institute of Marine Mechatronics Equipment, School of Mechanical Science and Engineering, Huazhong University of Science and Technology, Wuhan, China

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
12 March 2019 in Structural and Multidisciplinary Optimization
Verified
Journal Article
Closed access
PDF file
TTTengfei Tang
Tengfei Tang
LGLonglong Gao
Longlong Gao
BLBaoren Li
Baoren Li
LHLiao Li hui
Liao Li hui
YXYi Xi
Yi Xi
GYGang Yang
Gang Yang

6 July 2020 in IEEE Access
Verified
Journal Article
Open access
GYGang Yang
Gang Yang
PJPeng Jiang
Peng Jiang
LLLei Lei
Lei Lei
YWYong Wu
Yong Wu
JDJingmin Du
Jingmin Du
BLBaoren Li
Baoren Li
Using high-speed on-off valves (HSVs) with small size, low cost, and high switching accuracy instead of expensive proportional/servo valves, and researching high-performance vacuum servo system can further enhance the competitiveness of vacuum servo technology. However, due to the delay characteristics of high-speed on-off valve (HSV), the average gas mass flow rate of the output has dead zone, saturated zone and nonlinear zone. A linear compensation method for flow output is designed, so that the average gas mass flow rate of the output is approximately positively correlated with the duty cycle of the pulse width modulation (PWM) signal. Furthermore, because of the air compression and the leakage of the system, there exist parametric uncertainties, unmodeled dynamics and disturbances in the vacuum servo system. An adaptive backstepping control (ABC) strategy based on discontinuous projection mapping is designed. The adaptive backstepping control strategy inhibit the influence of system’s parametric uncertainties through on-line update of the uncertain parameters, and uses its own robustness to eliminate the effects of unmodeled dynamics and disturbances. Compared with the sliding mode control (SMC) strategy, the experimental results show that when the tracking frequency reaches 3–4Hz, the adaptive backstepping control strategy can ensure good tracking performance.

27 November 2017 in IEEE Journal of Oceanic Engineering
Verified
Journal Article
Closed access
LGLei Gao
Lei Gao
BLBaoren Li
Baoren Li
LGLonglong Gao
Longlong Gao
A gradual change of the pitch angle was observed for a glider in a sea trial in August 2014. It took place when the glider moved in both upward and downward glides between the sea surface and a depth of 1200 m and there was neither any internal mass movement nor buoyancy engine regulation in the steady glide. In this paper, this phenomenon is validated via a nonlinear dynamic model, which is restricted to the vertical plane. The model is based on Kirchhoff's equations of motion for a submerged rigid body and takes the seawater pressure, temperature, and density, and the deformation of the pressure hull of the glider into consideration. While the variations of aforementioned four parameters influence many physical parameters, including added mass, buoyancy, center of buoyancy (CB), hydrodynamic forces, and torques, their effects on glide velocity appear to be the primary cause for the gradual change of pitch angle observed. To minimize the gradual change of pitch angle, two effective approaches are proposed and validated, namely increasing the lift/drag ratio and decreasing the hydrodynamic torque coefficients.

21 June 2021 in IEEE Access
Verified
Journal Article
Open access
LHLiao Li hui
Liao Li hui
BLBaoren Li
Baoren Li
YWYuanyuan Wang
Yuanyuan Wang
YXYi Xi
Yi Xi
DZDijia Zhang
Dijia Zhang
LGLonglong Gao
Longlong Gao
In this paper, an observer-based adaptive fuzzy robust controller is proposed for trajectory tracking control of a bionic mechanical leg (BML) with unmeasured system states, dynamic uncertainties and external disturbances. A high gain observer (HGO) is constructed to estimate the unavailable joint velocities using the joint position feedback signals, while an adaptive fuzzy logic system (AFLS) is employed to address the lumped uncertainties. The nonlinear robust controller is then synthesized via backstepping method to improve the position tracking performance. The stability of the closed loop system is mathematically demonstrated via the Lyapunov’s stability theory. It is proven that under the proposed controller all the closed-loop signals are bounded and the trajectory tracking errors converge to a small neighborhood of the origin with appropriate design parameters. The effectiveness of the proposed control scheme is illustrated by simulation studies.

24 March 2022 in Entropy
Verified
Journal Article
Open access
PDF file
MNMBOULE NGWA
MBOULE NGWA
LGLonglong Gao
Longlong Gao
BLBaoren Li
Baoren Li
This paper uses heat transfer experiments and computational fluid dynamics (CFD) simulations to investigate the conjugate heat transfer (CHT) in a high-pressure pneumatic control valve assembly. A heat transfer test rig was constructed, and time–temperature histories of five test points placed on the valve assembly’s outer surface were recorded for study validation. The Unsteady Reynolds-Averaged Navier–Stokes (URANS) CFD methods with the standard k-ε turbulence closure equations were adopted in the numerical computations. Polyhedral grids were used; time step and mesh convergence studies were conducted. Simulated and measured temperatures profile comparisons revealed a good agreement. The CHT results obtained from CFD showed huge velocity fields downstream of the valve throat and the vent hole. The airflow through the valve was icy, mainly in the supersonic flow areas. Low temperatures below 273.15 K were recorded on the internal and external walls of the valve assembly. The consistency of the measured data with the numerical results demonstrates the effectiveness of polyhedral grids in exploring the CHT using CFD methods. The local entropy production rate analysis revealed that irreversibility is mainly due to viscous dissipation. The current CHT investigation provides a potential basis for thermostress analysis and optimization.

13 October 2023 in Actuators
Verified
Journal Article
Open access
PDF file
SLSong Liu
Song Liu
BLBaoren Li
Baoren Li
RGRunlin Gan
Runlin Gan
YXYue Xu
Yue Xu
GYGang Yang
Gang Yang
This paper aims to optimize the two-stage helical pairs (TSHPs) in a helical hydraulic rotary actuator (HHRA) in terms of volume, transmission efficiency, and maximum contact stress. Volume and transmission efficiency can be determined through analytical mathematical models. However, calculating the contact stress of helical pairs necessitates complex and time-consuming finite element simulation. To address this issue, a method for predicting the maximum contact stress using an ensemble of metamodels (EMs) is proposed, with an automated finite element simulation process developed for data provision. The superiority of the EMs is validated through comparative analysis with three stand-alone metamodels. The optimization is carried out using the NSGA-II algorithm, including four combinations of the three objectives, and global sensitivity is analyzed over the objectives. The results indicate a trade-off relationship between maximum contact stress and volume in the optimal space. Moreover, considering multiple combinations enhances the robustness of the optimization results. The method is effectively applied to the design of the TSHPs and provides a new idea for the related actuator design.